Reference: YAESU-FC40-478
Automatic antenna tuner Yaesu FC-40 for transceivers FT-450, FT-857, FT-897 and FT-897D, FT-857D and FT-450D.The FC-40 automatic tuner is designed to be placed outdoors on the antenna mat, works with
Reference: YAESU-FC50-479
This Yaesu FC-50 automatic antenna tuner is specially designed for the FT-891 and for indoors, deskop or mobile used.The FC-50 automatic tuner antenna operates from 1.8-29Mhz and 50-54 MHz with a
Reference: DIAMOND-DAP600-1605
Diamond DAP-600 telescopic pole in 5 sections with diameters from 42 to 26mm, for a minimum height of 1.5m to a maximum of 6m, full extension. High strength anodised aluminium construction, complete
Reference: DIAMOND-SX1100-117
The SX1100 measures forward and reflected power and VSWR for 1.8-160Mhz, 430-450Mhz, 800-930Mhz and 1240-1300Mhz. Two directional couplers with switch and LED indicators for in-line connection of two
Reference: MTUNER-MAT-K100-1611
The mAT-K100 is an automatic antenna tuner operating in the 1.8MHz to 54MHz range, at power levels up to 120 watts. It allows tuning of dipoles, verticals, Yagis, or virtually any coax-fed antenna. It
Reference: MTUNER-MAT-180H-1610
The mAT-180H is an automatic antenna tuner operating in the 1.8MHz to 54MHz range, at power levels up to 120 watts. It allows tuning of dipoles, verticals, Yagis, or virtually any coax-fed antenna. It
Reference: ALPHA-DELTA-SWITCH-4B-N-1216
Robust antenna switch ALPHA DELTA 4B-N 4 positions with N female connectors for frequency use from 0 to 1600 Mhz.With robust switch shaft and precision machined mechanism for stable switching
Reference: DIAMOND-DAP450-1604
Diamond DAP-450 telescopic pole in 4 sections with diameters from 34 to 22mm, for a minimum height of 1.4m to a maximum of 4.5m, full extension. High strength anodised aluminium construction, complete
Reference: DIAMOND-CMF2000-1122
The Diamond CMF-2000 is a common mode filter that will prevent TVI and EMI CEM interference, caused by the transmission coaxial cable.Usable from 1 to 54 Mhz all bands, HF amateur radio, CB 27 Mhz,
Reference: ALPHA-DELTA-SWITCH-4B-PL-1215
Robust antenna switch ALPHA DELTA 4B-PL 4 positions with SO-239 connectors (UHF-female) for frequency use from 0 to 500 Mhz.With robust switch shaft and precision machined mechanism for stable
Reference: ALPHA-DELTA-SWITCH-2B-N-1214
Robust antenna switch ALPHA DELTA 2B-N 2 positions with N female connectors for frequency use from 0 to 1600 Mhz.With robust switch shaft and precision machined mechanism for stable switching
Reference: DIAMOND-AS603-1603
The AS603 tripod is designed for the DAP-450 and DAP-600 masts. The holder is equipped with an adapter ring, so that the two masts with different diameters are held securely. Other masts can be used
Reference: KOMUNICA-SX201-1662
The Komunica SX-201 VSWR Meter allows the measurement of VSWR for frequencies from 1.8 to 200 MHz with a power up to 200 Watts (HF). Supplied with: 1 SX-201, 1 12V power cable.
Reference: ALPHA-DELTA-SWITCH-2B-PL-1213
Robust antenna switch ALPHA DELTA 2B-PL 2 positions with SO-239 connector (UHF-female) for frequency use from 0 to 500 Mhz.With robust switch shaft and precision machined mechanism for stable
Reference: YAESU- ATBK-100-977
The Yaesu ATBK-100 is a counterpoise kit for the ATAS-120 motorized antenna.The ATBK-100 improves the ground plane for the VHF-UHF bands of 70cm (430Mhz), 2m (144Mhz) and 6m (50Mhz).Does not work for
Reference: DIAMOND-K9000-129
Diamond K9000 is a motorized mount antenna with remote control system and ability to adjust angle from 0 to 90 degrees in for 4 seconds! Designed to raise and lower HF/VHF/UHF mobile antennas that do
Reference: DIAMOND-MX2000N-901
Diamond MX-2000N Triplexer HF/50/144/430Mhz with PL-259 (HF and VHF) cable and N (UHF) cabler, Diamond Antenna (Japan) original warranty. Also available the MX2000 version with male UHF connector
Reference: KOM-MX-1300-PWR-C-1204
Komunica Triplexer with cables:1.6-160MHz (PL)350-550MHz (N)850-1300MHz (N)In Connector: N female Impedance: 50 Ohm VSWR: < 1.2 - PL-259: 1.6-160MHz = 800W (PEP) / 0.20 dB
Reference: KOM-MX-2000-PWR-N-1206
Triplexer 1.6 -60 / 110-170/350-570MHZ, with cables. Connector: SO-239 Connectors end cable: 2 x PL-259 + 1 N male - PL-259: 1.6-60MHz = 800W (PEP) - PL-259: 100-170MHz = 800W (PEP) - N male:
Reference: DIAMOND-MX62N-612
Duplexer Diamond MX62N and MX62M, Diamond Japan original warranty, covers from 1.6 to 56MHz for HF bands and from 120 to 470Mhz, in transmission and reception. The MX62N duplexer is perfect to use
Reference: KOM-MX-1300-PWR-N-1205
Triplexer without cables: 1.6-160 (SO-239) 350-550 (N female) 850-1300MHz (N female) IN connector: N female - SO-239: 1.6-160MHz = 800W (PEP) / 0.20 dB (Insertion Loss) - N
Reference: DIAMOND-K600-135
Diamond K600M is a aerodynamic design trunk mount for heavy duty mobile antenna. Recommended for high-gain VHF/UHF antennas. FeaturesVertical adjustment range 0-9°Four set screwsStainless steel mount
Reference: DIAMOND-SS500-143
Diamond SS500 splitter/combiner for recieving from 0.5 to 500MHz, serves to connect 2 differents antennas to 1 receiver or 1 antenna to 2 receivers. Impedance:50ohmsWeight:130g Connector: SO-239
Reference: DIAMOND-MGC50-144
Diamond MGC50 is a window through SO-239 cable set. Length:50cm (Between connectors)Weight:102g Freq.: 0 to 1500MHz
Reference: KOM-PWR-SW3N-1198
3 position coaxial antenna switch with N female connector.For use in frequency from 0 to 1500 Mhz.
Reference: KOMUNICA-SX40-1660
The SX40 is a cross needle SWR/ROS meter with direct and reflected power indication. It allows direct reading of VSWR and power output from the crossing of the two needles. Supplied with: 1 SX-40, 1
Reference: COMET-CF416A-987
COMET CF-416 duplexer / combiner / splitter, to separate HF/VHF frequencies from 1.3 to 170 Mhz and UHF band 350 to 540 Mhz.Available in 2 versions with PL-259 or N connectors for the UHF band. The
Reference: DIAMOND-SX27P-397
SWR-meter and watt meter portable, original Diamond SX-27P for VHF bands from 140 to 150MHz and UHF band from 430 to 450MHz, it can measure the SWR and power (60 watts maximum). Operating
Reference: KOM-MX-620-PWR-M-1208
Duplexer 1.6-56 Mhz (HF+6m) & 140-470MHz (VHF+UHF), with cable. Connector: SO-239 Cable Connectors: 2 x PL-259 - PL-259: 1.6-56MHz - 600W (PEP) - PL-259: 140-470MHz - 600W (PEP)
Reference: DIAMOND-K33
Diamond K33 tilt angle adjustable mount bracket for heavy duty type. Coaxial cable with SO-239 socket (UHF female) compatible: Diamond RG3MR or RG6MR, SO-239 Nagoya socket cable.
Reference: CHA-ANT-BPACK-1559
The CHA BPACK is Chameleon Antenna's backpack: built to last, configurable according to your needs, ergonomic, with internal and external storage. It is designed to support radio operators of all
Reference: QO100-ANALOG-CN0417-777
The Analog Devices CN0417 is a small RF power amplifier, powered by micro-USB, optimized to operate on 2400 MHz with 100mW max, gain of 20-21dB max., with a integrated bandpass filter 2400 to
Reference: KOM-MX-600-PWR-N-1207
Komunica duplexer. Frequency Range: 1.6-150MHz N female 400-460MHz N female IN connector: N female
Reference: KOM-MX-720-PWR-N-1210
Duplexer 1.6-150 & 400-470MHz, with low loss cable. Connecteur: SO-239 Connecteurs: 1 x PL-259 + 1 N mâle - SO-239: 1,6-30MHz = 1KW (PEP) / 50-150MHz = 400W (PEP) - N mâle: 400-460Mhz = 240W (PEP)
Reference: DIAMOND-MCRMSMA-142
Diamond MCRMSMA is a magnet base bracket for handheld transceivers and any devices with SMA connector. Coaxial cable: RG58 2.5m Connector: SMA Male / SMA FemaleMagnet diameter: 53mm
Reference: DIAMOND-MX72N-145
HF VHF UHF Duplexer Diamond MX72N. Passband width: LPF/1.6 to 30MHz 49 to 150MHz, HPF/400 to 460MHz (LPF:1.6 to 225MHz, HPF: 340 to 1000MHz receiving only) Power rating: 1.6 to 30MHz: 400W
Reference: DIAMOND-MCRMBNC-1036
Diamond MCRMBNC is a magnet base bracket for handheld transceivers and any devices with BNC connector. Coaxial cable: RG58 2.5m Connector: BNC Male / BNC FemaleMagnet diameter: 53mm
Reference: KOM-PWR-SW2N-1197
Commutateur d'antenne 2 positions avec connecteur fiche N femelle. Pour utilisation en fréquence de 0 à 3000 Mhz (3 Ghz).
Reference: SIRIO-EMBASE-MAG145-3-8-1654
This 16cm diameter SIRIO magnetic base allows to screw an antenna with 3/8x24 thread to be placed on a car roof or any metal surface of 1m² minimum. With RG58 coaxial cable and PL-259 connector (UHF
Reference: DIAMOND-MRX-141
Diamond MRX is a magnet base bracket for handheld transceivers and any devices with BNC connector. Coaxial cable: RG58 3m Connector: BNC Male / BNC FemaleMagnet diameter: 76.5mm
Reference: DIAMOND-MX72H-146
HF VHF UHF Duplexer Diamond MX72H.
Reference: KOM-MX-720-PWR-D-1209
Duplexer 1.6-150 & 400-460MHz, without cable. Connector: SO-239 Connectors: 2 x SO-239 - SO-239: 1.6-30MHz = 1KW (PEP) / 50-150MHz = 400W (PEP) - SO-239: 400-460Mhz = 240W (PEP)
Reference: KOM-TRIPLE-MAG-1659
Komunica reinforced magnetic base with triple magnet. Super-robust version and maximum grip. Base connector type SO-239 + 5 m RG-58 connector type PL-259 Delivered with : Triple mag magnetic base, 1 x
Reference: DIAMOND-K44L-128
Diamond K44L support for mounting a mobile antenna on a car's roof rack or a 1.5cm to 4cm tube.Support with adjustable tilt angle.Diameter accepted: 15mm to 40mm Coaxial cable with SO-239 socket (UHF
Reference: DIAMOND-K512-132
K-512 Diamond Roofrail Mounting Bracket 3-axis adjustable. Mast diameter accepted: 15-34mmRooftop railing Height accepted: Less than 32mm Width accepted: I 50mmSquare mast side length accepted:
Reference: QO100-FILTRE2-NMRF-944
The NMRF filter is a bandpass filter centered on 2450Mhz with a bandwidth of 150Mhz, for use in frequency from 2400 to 2500Mhz with a maximum power of 10W, for radio applications: Wifi, Zigbee, Drone
Reference: DIAMOND-K550-1121
2-axis swivel antenna mounting bracket, Diamond K500 and K550L for car roof rack and racks with large sections.Available in 2 versions:K550 for bars less than 50mm wideK550L for bars less than 75mm
Reference: DIAMOND-BU50A-517
Diamond BU50/A balun 1:1, genuine, operates from 1.7 to 40Mhz and allows to receive and transmit on HF bands.Technical data sheet of the HF BU50A balun:● Operating frequency from 1.7 to 40MHz●
Reference: DIAMOND-K515-1468
Diamond K512 mounting bracket with 2 adjustable pins for roof rack and bars, car luggage rail. Ramp height accepted: 50mm max. Accepted width: 48mm max. Coaxial cable with SO-239 socket (UHF female)
Reference: SIRIO-EMBASE-PM125-1655
This 12.7cm diameter SIRIO magnetic base allows you to screw on a 3/8x24 antenna for mounting on the roof of a car or any metal surface of 1m² minimum. With 3.6m RG58 cable and PL-259 connector. The
Reference: F1OPA-WIDEBAND-LNA3-805
Wide-band LNA preamp, based on PGA-103+, to improve reception performance from 50 Mhz to 1500 Mhz, with a maximum gain of 20-24dB and a noise factor of 0.4dB.This VHF-UHF LNA offers a very good
Reference: COMET-BOBINE-HFJ2M-1451
The COMET CCB-HFJ choke allows to add the 2m band (145MHz) to the COMET HFJ-350M portable and SOTA COMET HFJ-350M antenna (not included).- Frequency : 144-148 MHz- Type: 1/2 wave- SWR: 1.5 or less-
Reference: SIRIO-EMBASE-PM100-1656
This 9.2cm diameter SIRIO magnetic base allows to screw an antenna with 3/8x24 thread for installation on a car roof or any metal surface of minimum 1m². With 3.6m RG58 cable and PL-259 connector.
Reference: DIAMOND-MAT50-625
To use an HF antenna below 50Mhz band, a ground plane are required. This is not always possible or easy especially for antennas with magnetic base or for installations on a balcony. Diamond MAT-50
Reference: SIRIO-EMBASE-MAG145-371
This 12.5cm diameter SIRIO magnetic base allows a PL-259 (UHF-male) antenna to be screwed to place on a car roof or any metal surface of at least 1m².The magnetic base can support large antennas over
Reference: DIAMOND-RG6MR-RG58U-269
The cable antenna RG6MR Diamond is a length of 6 meters and allows you to connect an antenna with base PL259 (male UHF) on the SO239 socket (UHF female). It is equipped with a SO239 and RG58U cable
Reference: WIMO-CABLE-EMBASE-SO239-954
Base for drilling support, with SO239 connector (female UHF) for screwing the antenna.The 6mm RG58U 50ohms cable is 4 meters long and has a PL259 (UHF Female) connector at its end.
Reference: DIAMOND-HRK-134
Adhesive backed Diamond HRK for flat surface installations including glass, fiberglass, and metal. Can be used on the body of a car for an antenna less than 1m long.
Reference: DIAMOND-SUPPORT-KB2-1466
Diamond KB2 mounting bracket for installing an antenna base on a motorcycle. UHF female socket (SO-239) with PL-259 cable: Diamond RG3MR.
Reference: QO100-FILTRE-TAOGLAS-BPF.24-942
The Taoglas Airvu 2.4Ghz bandpass filter is a 100Mhz broadband filter, for use in frequency from 2400 to 2500Mhz and a maximum power of 10W.Connector 1: RP-SMA MaleConnector 2: RP-SMA Female Note: The
Reference: DIAMOND-CLB-1661
The Diamond CLB is a robust mounting bracket for attaching a mobile antenna to a mast with a diameter of 10 to 52mm. This mount accepts antenna bases (not included) and standard SO-239 (UHF female).
Reference: DIAMOND-BU55-538
Genuine Diamond BU55 balun 1:1, operates from 3 to 75Mhz, allows to receive and transmit on HF bands + 6 meters (50Mhz).Technical data sheet of the HF BU55 balun:● Operating frequency from 3 to 75MHz●
Reference: DIAMOND-RG3MR-3M-362
The cable antenna RG3MR Diamond is a length of 3 meters and allows you to connect an antenna with base PL259 (male UHF) on the SO239 socket (UHF female). It is equipped with a SO239 and RG58U cable
Reference: KOM-EMBASE-MAG2-BK1600-1000
Magnetic base of 16cm in diameter for screwing a PL-259 antenna (UHF-male) to land on a car roof or any 1m² minimum metal surface. The BK1600 magnetic base from CRT France, allows support of large
Reference: RTLSDR-LNA2-WIDEBAND-764
This wide-band LNA preamp improves reception performance from 50 Mhz to 4 Ghz, it is based on SPF5189Z, with a noise factor of less than 1 dB.This LNA is designed to be powered by BIAS-T with a power
Reference: FILTRE-SAW-QO100-F1OPA-824
This bandpass filter for the 2.4 Ghz (13cm) allows to reject the local oscillator and harmonics frequencies of the Up-Converter for QO-100 to get a clean signal on the satellite, with a max. input
Reference: K40-K40MM-1576
Heavy duty 3/8x24 stainless steel K40MM antenna mirror mount, designed for all 3/8 x 24 antennas (including K40 antenna), with female UHF connector (SO-239) to connect the coaxial cable. 60 mm
Reference: MTUNER-MAT-CK-1613
mAT-CK interface cable to connect the mAT-180H automatic tuner to a KENWOOD transceiver.
Reference: MTUNER-MAT-CI-1614
mAT-CI interface cable to connect the mAT-K100 automatic tuner to an ICOM transceiver.
Reference: KOM-EMBASE-MAG3-BM1PL-1001
Strong magnetic base mount of 12cm in diameter for screwing a PL-259 antenna (UHF-male) to land on a car roof or any 1m² minimum metal surface. The BM-1-PL Komunica magnetic base, allows support of
Reference: KOM-EMBASE-BK-1500-539
This 15cm diameter magnetic base ensures a solid fixation and allows to screw a PL-259 antenna (UHF-male) on a car roof or a metal surface of minimum 1m².The magnetic base allows to support antennas
Reference: OPA-BOITIER-941
This milled aluminum milled box is specially designed for the RF protection of PCBs from F1OPA Design: LNA VHF-UHF, Bias-T, 2.4Ghz amplifier, SAW 868Mhz filters, ADS-B, QO-100 2.4Ghz and HF LNA.Case
Reference: NAGOYA-L20-UHF-456
This dummy load 50 ohms Nagoya L20 runs from 0 to 500MHz with a maximum power of 15W or 100W (during 2 seconds max), with UHF male connector (PL-259) or N male plug (choose below). Genuine Nagoya
Reference: NAGOYA-RB500-1067
Nagoya RB-500 universal support for mounting a mobile antenna on a 4-door car, to be installed on a car trunk or trunk lid.Adjustable and adjustable according to 3 axis.Supplied with: Nagoya RB-500
Reference: NAGOYA-RB600-1068
Nagoya RB-600 universal support for mounting a mobile antenna on a 5-door car, to be installed on hatchback car. Adjustable and adjustable according to 3 axis.Supplied with: Nagoya RB-600 hatchback
Reference: QO100-OPA-BIAS-T1-760
This BT4G-based BIAS-TEE with SMA female connector is used to power a LNA or a 10Ghz PLL LNB to receive the QO-100 / Es'Hail2 satellite.The BT4G covers the frequency bands from 30 MHz to 4 GHz. The
Reference: NAGOYA-SUPPORT-RB56-870
Nagoya RB56 mount bracket for mounting a mobile antenna on a car gutter. 1 angle adjustable.Come with: 1 Nagoya RB56 genuine mount bracket, without cable (optional below). Coaxial cable with SO-239
Reference: NAGOYA-RB700-1070
Nagoya RB-700 genuine universal support for mounting a mobile antenna on a 5-door car, to be installed on hatchback car. Adjustable and adjustable according to 2 angles.Supplied with: Nagoya RB-700
Reference: NAGOYA-RB400-138
Nagoya RB-400 antenna support for mounting a mobile antenna, to mount on trunk lid, 4-door car. 2 angle adjustable.Delivered: Nagoya support RB-100 genuine, without cable (optional below). Coaxial
Reference: NEBRA-EMBASE-MAG-NBR-0038N-1532
This magnetic base is used to fix an antenna with an N plug on a metal surface. Supplied with 2m LMR200 coaxial cable and RP-SMA male connector . Frequency: 0 to 6GHz VSWR: ≤ 2.0 Maximum input power:
Reference: NAGOYA-RBCLPSP-SMAF-530
This Nagoya mounting bracket allows to deport a walkie-talkie antenna to fix it on a window car. Antenna support connector: SMA Male Antenna cable connector: SMA Female, SMA male or BNC Male (to
Reference: NAGOYA-RB16-BNC-1066
Nagoya RB-16 magnetic base with female BNC antenna support connector, with male BNC connector coaxial cable.For example, allows the BNC antenna of a walkie-talkie to be moved to the roof of a car to
Reference: NAGOYA-COAX-RG58-4M-534
The cable is a length of 4 meters and allows you to connect an antenna with base PL259 (male UHF) on the SO239 socket (UHF female). It is equipped with a SO239 and RG58 50ohms cable and the other
Reference: RG316-UHF-5M-1671
Screw-on base in SO-239 (UHF female) with 5 meter RG-316 coaxial cable and PL-259 connector (UHF male). For mounting a PL-259 screw-on antenna. Connector 1: UHF Female (SO-239)Connector 2: UHF Male
Reference: NAGOYA-RB16SP-SMA-F-529
Magnetic mount Nagoya RB-16-SP with antenna support connector in SMA male, for walkie-talkie to deport the antenna of the handheld (for example in car or at home).Coaxial cable: RG174 50 Ohms 3 meters
Reference: ADAPT-UHF-M-HD-F-1657
RF adapter with PL-259 (UHF Male) to 3/8x24 female connector. Allows the use of 3/8x24 threaded whips on PL-259 mounts. Robust design for heavy load and antenna. Impedance: 50 ohms
Reference: ADAPT-DIAMOND-SMAJSMAJ-276
Adapter for walkie-talkie, handheld VHF-UHF or scanner equipped SMA to use SMA antennas.- The adapter has a SMA Female connector on one side and the other is SMA Female- The design is specially
Reference: NAGOYA-RB20B-148
Mini Nagoya RB-20B Hatchback Door, trunk lid mount Antenna Bracket. Shipped with: 1 Nagoya RB-20B genuine, without cable (in option below). Coaxial cable with SO-239 socket (UHF female) compatible:
Reference: SIRIO-SUPPORT-M1-657
Stainless steel mounting bracket SIRIO M-1. Allows the installation of mobile or portable antenna. Size: 3,8 x 6,4 x 9,9 cm. Delivered with: 1 bracket only SIRIO M-1, without base or coaxial cable
Reference: MIDLAND-SP21-639
Mounting bracket for mirror or metal rod. Allows the installation of any mobile type antenna. Delivered with: 1 bracket only, without base or coaxial cable (optional)
Reference: SIRIO-ASP-1-CHROME-1253
Antenna mounting bracket, on mirror rod, Sirio ASP-1 Chrome. Maximum mounting diameter Ø 16 mm, in galvanized steel. Supplied with: 1 Sirio ASP-1 Chrome.
Reference: CRT-CORDON-BNC-90CM-444
BNC-BNC cable 90 centimeters with 6mm RG58 coaxial cable 50 ohm and 2 BNC-Male connectors assembled.
Reference: ADAPT-SMA-M-BNC-F2-275
RF adapter for walkie-talkie, handheld VHF-UHF or scanner, equipped with SMA female connector and to use a BNC male antenna. - The adapter is equipped with an SMA Male connector on one side and the
Reference: ETUI-ANT-ABBREE-1670
Khaki green nylon case for military style tactical walkie talkie antenna, such as the Abbree antenna. Ideal for protecting and storing the folded antenna when not in use. Attaches to a backpack.
Reference: WA5-PCB-MMIC-SMA-774
MMIC prototype circuit on PCB for connection with SMA connectors (available as an option below).Supplied without SMA connector (solder).Fits standard SMA PCB connectors, including with SMA
Reference: SIRIO-DV-SCREW-BOLT-CHROME-1257
Screw and bolt, chrome, for Sirio antennas with DV mount (DV-Mount).
Reference: NAGOYA-UHFPU213-PL259-11MM-375
PL259 long socket connector (UHF male) for coaxial cable 11mm weld.
Reference: NAGOYA-UHFPU58-PL259-6MM-374
PL259 short socket connector (UHF male) for coaxial cable 6mm weld. Other model available: PL 259 6mm in teflon.
Reference: ADAPT-RSP2-582
Connector for Hi-Z antenna of the SDRPlay receiver RSP2 and RSP2PRO. 5.08 female connector with 3 poles.
Reference: CABLE-VENTION-VELCRO-KAC00-853
Cable hook scratch with buckle for fixing on the cable.Delivered with: Velcro velcro cable tie Vention with buckle. Sold individually.
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal