Our store uses its own and third-party cookies to improve our services, secure transactions and enable tracking. To give your consent to its use, press the Accept button or choose Cookies.
Please note that refusing the Paypal cookie will prevent this payment method from being displayed and working in our store.
Viewed products
M&P-Flux for soldering printed...
M&P-Flux for soldering printed microcircuits can be used in both the soldering and de-soldering phases.
Improved thermal conductivity and capillarity: Its chemical composition facilitates the entry of molten tin, causing it to be drawn by "capillary action" into the hole of UHF EVO pins, or N-pins or PL259 connectors and any other solder connector.
The capillary phenomenon described above generates a higher soldering speed, resulting in less thermal stress to the coaxial cable dielectric which could be deformed by prolonged heat.
The resulting solder joint is never cold and opaque, but bright and reliable, in a shorter time.
To desolder on the contrary, using the desoldering braid combined with M&P-Flux while heating the interested parts with the soldering iron, we will see a reverse effect of the tin flow which this time, always sucked by capillarity, as if by magic, will be attracted by the desoldering braid, leaving the connector clean and perfectly reusable.
M&P-Flux must be applied with the special mini tube dispenser inside the hole, in small quantities. Then place the tin wire, and the tip of the soldering iron at the temperature of 300°-350°C. The soldering will be done exactly where it is needed, avoiding short circuits and saving you time and money.
CAUTION: As with any product of this type, it is essential to keep it out of the reach of children. The product is harmful if swallowed, causes skin irritation or severe eye irritation if touched. In case of contact with eyes, wash immediately and call a specialist. Wash hands thoroughly after use or use latex gloves instead. Use in an open or ventilated area, or remove fumes with a suitable extraction system. All of these precautions apply to any soldering activity (solder can be 30-40% lead, whereas M&P Flux is ROHS compliant - lead free, so as it reduces soldering time, you are less exposed to tin-lead fumes).
PL259 short socket connector (UHF male) for coaxial cable 6mm weld. Other model available: PL 259 6mm in teflon.
1,67 €tax excl.
PL259 long socket connector (UHF male) for coaxial cable 11mm weld.
2,08 €tax excl.
UHF Male (PL-259) to soldering Messi & Paoloni connector for M&P AIRBORNE 5 and RG58 C/U 5mm coaxial cable.New design with double seal to ensure perfect protection against water infiltration,
5,42 €tax excl.
UHF Male (PL-259) to soldering, Messi & Paoloni connector for M&P HYPERFLEX 5.New design with double seal to ensure perfect protection against water infiltration, humidity and
4,92 €tax excl.
UHF Male connector (PL-259) to soldering, Messi & Paoloni for 10.3mm coaxial cable M&P AIRBORNE 10, HYPERFLEX 10, ULTRAFLEX 10 and RG213 PLUS.New design with double seal to ensure perfect
6,58 €tax excl.
UHF Male connector (PL-259) to soldering, Messi & Paoloni for 7mm coaxial cable M&P ULTRAFLEX 7.New design with double seal to ensure perfect protection against water infiltration, control and
6,58 €tax excl.
N Male connector to soldering, Messi & Paoloni for M&P coaxial cable HYPERFLEX 5.New design with double seal to ensure perfect protection against water infiltration, humidity and
5,75 €tax excl.
N Male connector to soldering, Messi & Paoloni for M&P coaxial cable AIRBORNE 5 and for RG58 cable.New design with double seal to ensure perfect protection against water infiltration, humidity
5,75 €tax excl.
Click here to leave a review
Be the first to ask a question about this product!
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal