Exceptional closure: From January 22 to 29, 2021, shipments resumes from February 1, 2021.
Subcategories
Reference: ETTUS-BOITIER3-B205-809
Ettus official protective metal case for the USRP B205MINI SDR transceiver. This enclosure kit allows users to assemble a steel case to protect the B205MINI-i board-only device, and increases
Reference: ETTUS-BOITIER2-B210-807
Ettus official protective metal case for the USRP B200 and B210 SDR transceiver Green PCB series only. This enclosure kit allows to assemble a steel case to protect the B200/B210 board-only device,
Reference: CROWD-LIMESDR-BOITIER2-676
Official Lime Micro acrylic case for LimeSDR transceiver. Delivered with: 1 acrylic box to mount for LimeSDR. Antenna not supplied (in option).
Reference: GSG-GREATFET-831
Designed to succeed the GoodFET project the GreatFET One is a universal USB device. By adding expansion cards called "neighbors", you can turn GreatFET One into a USB device that does almost
Reference: CONTOUR-SHUTTLE-PRO-V2-799
The Shuttle PRO V2 Contour Design allows to control the frequency of a SDR software and to retrieve the classic operation of a VFO on SDR radio equipment!The Shuttle PRO V2 includes 15 programmable
Reference: ETTUS-LP0965-359
This directional Log Periodic antenna is designed in PCB and operates from 850MHz to 6,5GHz with 5-6 dBi gain. Works with Ettus USRP B200mini and all equipment operating in this frequency range. The
Reference: DIAMOND-SS500-143
Diamond SS500 splitter/combiner for recieving from 0.5 to 500MHz, serves to connect 2 differents antennas to 1 receiver or 1 antenna to 2 receivers. Impedance:50ohmsWeight:130g Connector: SO-239
Reference: RASPBERRY-PI4-2G-909
The new Raspberry Pi 4 B has a Quad Core 1.5Ghz 64bits processor, 2.4Ghz / 5Ghz WiFi functions, Bluetooth Low Energy (BLE 5.0), 2GB memory or 4GB DDR, dual video display with resolution up to 4K, USB
Reference: ETTUS-BOITIER-B200MINI-493
Ettus official protective metal case for the USRP B200 MINI SDR transceiver. This enclosure kit allows users to assemble a steel case to protect the B200MINI board-only device, and increases operating
Reference: QO100-ANALOG-CN0417-777
The Analog Devices CN0417 is a small RF power amplifier, powered by micro-USB, optimized to operate on 2400 MHz with 100mW max, gain of 20-21dB max., with a integrated bandpass filter 2400 to
Reference: CONTOUR-SHUTTLE-XPRESS-297
Allows to control by USB the change of frequencies of an SDR software and to get a classic operation of a VFO on a radio hardware SDR!Fully configurable with the supplied software, Shuttle Xpress is
Reference: DIAMOND-MCRMSMA-142
Diamond MCRMSMA is a magnet base bracket for handheld transceivers and any devices with SMA connector. Coaxial cable: RG58 2.5m Connector: SMA Male / SMA FemaleMagnet diameter: 53mm
Reference: DIAMOND-MCRMBNC-1036
Diamond MCRMBNC is a magnet base bracket for handheld transceivers and any devices with BNC connector. Coaxial cable: RG58 2.5m Connector: BNC Male / BNC FemaleMagnet diameter: 53mm
Reference: NOOELEC-100555-HAM-IT-UP-44
Nooelec's Ham It Up v1.3 is an up-converter HF, equipped with the 125Mhz filter soldered on the PCB and allows to listen to all MF / HF bands from 0.5 to 50 Mhz, in all modes of modulation, from a
Reference: RASPBERRY-PI3-PLUS-09
The new Raspberry Pi 3 model B & B+ features a 1.4Ghz Quad Core processor, WiFi 2.4Ghz / 5Ghz and Bluetooth Low Energy (BLE), making it even easier to develop RF and IoT radio applications. CPU
Reference: NUAND-TX-BT100-928
The BT-100 is a TX power amplifier, powered by Bias-T, to connect to the SMA TX socket of the bladeRF 2.0 micro xA4 and xA9.MMIC: PHA-1H +TX frequency: 50 MHz to 6 GHzConsumption: 200mWBlue LED power
Reference: NUAND-RX-BT200-929
The BT-200 is a RX LNA, powered by Bias-T, to connect to the SMA RX socket of the bladeRF 2.0 micro xA4 and xA9.MMIC: TSS-53LNB+TX frequency: 500 MHz to 5 GHzConsumption: 300mWGreen LED power
Reference: NOOELEC-100799-NOAA-1061
This SawBird + filter from Nooelec is specially designed to operate on the NOAA 137 Mhz frequency band and for NOAA weather satellite reception applications.It makes it possible to significantly
Reference: LNA4ALL2-288
Preamplifier and LNA (low noise amplifier) specially adapted with BIAS-T for HackRF One, AirSpy, SDRPlay and RTL-SDR V3 usb stick. It highly increases the reception performance (+ 11dB to + 23dB) and
Reference: CROWD-LIME-MINI-ANT-669
Two omnidirectional antennas with male SMA connectors, compatible with LimeSDR mini and HackRF One, optimized for LTE, 4G, HSPA, UMTS, 3G, EDGE, GPRS frequency ranges of 800-960 MHz, 1710-2170 MHz and
Reference: LNA4ALL-285
The LNA4ALL is a pre-amplifier and a low-pass filter (LNA) with SMA female RF connectors and for RF frequencies covering all bands from 28MHZ to 2500 MHz. It improves greatly reception performance, on
Reference: QO100-FILTRE2-NMRF-944
The NMRF filter is a bandpass filter centered on 2450Mhz with a bandwidth of 150Mhz, for use in frequency from 2400 to 2500Mhz with a maximum power of 10W, for radio applications: Wifi, Zigbee, Drone
Reference: NOO-BOITIER-LANA-100812-908
Nooelec's LANA is a high-gain, 20 MHz - 4 GHz wide band LNA amplifier for SDR applications, with low power consumption and better linearity than the SPF5189Z LNA.The LaNa has 3 different power
Reference: F1OPA-WIDEBAND-LNA3-805
Wide-band LNA preamp, based on PGA-103+, to improve reception performance from 50 Mhz to 1500 Mhz, with a maximum gain of 20-24dB and a noise factor of 0.4dB.This VHF-UHF LNA offers a very good
Reference: CROWD-LIME-MINI-BOITIER-668
Official Lime Micro case for SDR dongle transceiver LimeSDR mini. Delivered with: 1 official box LimeSDR mini acrylic, without antenna nor LimeSDR mini included.
Reference: NOO-BOITIER2-HACKRF-NOIR-999014-
Nooelec aluminium case V2 (new version) specifically designed for HackRF One reduce parasitic interference nearby and add a stronger resistant case. This aluminum case is for replacing the original
Reference: OPA-LNAHF-HFLNA-284
The LNA HF from F1OPA is a pre-amplifier and a low-pass filter (LNA), very powerful (+18dB to +20dB), with SMA Female connectors, for HF frequencies and short waves from 500 kHz to 30 MHz, with
Reference: QO100-FILTRE-TAOGLAS-942
The Taoglas Airvu 2.4Ghz bandpass filter is a 100Mhz broadband filter, for use in frequency from 2400 to 2500Mhz and a maximum power of 10W.Connector 1: RP-SMA MaleConnector 2: RP-SMA Female Note:
Reference: ANT-AL-MINI-WHIP-87
This Mini-Whip SDR active antenna allows reception of HF frequencies from 0 to 50 mhz with an SDR receiver.Compact in size, the mini-whip active antenna can be used independently with a 9-volt battery
Reference: NOOELEC-100722-OUTERNET-467
This LNA and SAW filter from Nooelec is specially designed to operate on 1.5Ghz Outernet frequency band and for Inmarsat radio applications, covering from 1.50GHz to 1.58GHz. It significantly
Reference: MINIVNA-CALIBRATION-727
This calibration kit can be used with any SMA connector device, such as the MiniVNA Tiny and PRO2.The SMA calibration kit consists of a dummy load of 50 ohms, an open circuit and a short
Reference: DIAMOND-HRK-134
Adhesive backed Diamond HRK for flat surface installations including glass, fiberglass, and metal. Can be used on the body of a car for an antenna less than 1m long.
Reference: NUAND-BLADERF-BOITIER-385
Genuine case for Nuand BladeRF X40 or x115.
Reference: NUAND-BOITIER-BRFM-666
Official case for the Nuand bladeRF 2.0 micro, version xA4 and xA9. A set of screws is included for assembly. The case is made of polycarbonate material high density, transparent and very
Reference: FILTRE-SAW2-868-F1OPA-830
This filter for the 868 Mhz bandpass improves selectivity and suppresses spurious signals outside the 868Mhz band.Utilization type unlicensed ISM bande 868 Mhz: Sigfox, LoRa, LoRaWAN.Supplied with: 1
Reference: RTLSDR-LNA2-WIDEBAND-764
This wide-band LNA preamp improves reception performance from 50 Mhz to 4 Ghz, it is based on SPF5189Z, with a noise factor of less than 1 dB.This LNA is designed to be powered by BIAS-T with a power
Reference: NOO-100672-BOITIER-BLEU13-3153
Provides an effective protection against impact and parasites for your converter HF SDR Ham It Up and also gives it a nice looking. The enclosure is made of aluminum and laser engraved, with 2
Reference: NOOELEC-TCXO-HACKRF-100773-719
This ultra-flat 10 MHz Tiny TCXO module is for HackRF One. This 0.5 ppm TCXO improves performance with ultra-low phase noise and high frequency stability in almost any condition.Perfect for any high
Reference: FILTRE-SAW-QO100-F1OPA-824
This bandpass filter for the 2.4 Ghz (13cm) allows to reject the local oscillator and harmonics frequencies of the Up-Converter for QO-100 to get a clean signal on the satellite, with a max. input
Reference: KOM-EMBASE-MAG-BK1400-371
Magnetic base of 14cm in diameter for screwing a PL-259 antenna (UHF-male) to land on a car roof or any 1m² minimum metal surface. The BK1400 magnetic base from CRT France, allows support of large
Reference: ANT-XLA-MINI-WHIP2-1012
Active Whip mini-antenna for receiving HF frequencies from 10khz to 30 mhz with an SDR receiver or a short and HF receiver. Antenna connector: SMA female.This active antenna need to be powered with
Reference: FILTRE-RTLSDR-FM-473
This band-cut filter is design by RTL-SDR.com, it blocks and reject broadcast FM band between 88 to 108 MHz with over 50dB of attenuation. Insertion loss is less than 0.5 dB between 0-1 GHz, and less
Reference: FILTRE-RTLSDR-523
This high-pass notch filter is designed by RTL-SDR.com and rejects the AM broadcast from 500 kHz to 1.7 MHz, with attenuation of more than 50dB. In fact, because of the attenuation, the filter is
Reference: OPA-BOITIER-941
This milled aluminum milled box is specially designed for the RF protection of PCBs from F1OPA Design: LNA VHF-UHF, Bias-T, 2.4Ghz amplifier, SAW 868Mhz filters, ADS-B, QO-100 2.4Ghz and HF LNA.Case
Reference: NUAND-XB200-BOITIER-383
Case for transverter Nuand XB200.
Reference: NOO-100814-BALUN2-907
The new version Nooelec Balun 1:9 v2 allows to add a wired or dipole antenna type to listen HF bands from 0 to 30Mhz from the Ham It Up converter, an SDRPlay receiver or equivalent covering the HF
Reference: CABLE-RIPCORD-12V-8002
With the Ripcord USB power cable, you have the freedom to power anywhere you are any device in 5, 9 or 12V from a USB port of a laptop, from an external battery or from a smartphone/tablet (with OTG
Reference: ANT-GPS-USB-BN82U-887
GPS antenna with adhesive support and USB cable.This USB GPS antenna is compatible on Windows, Mac OS and Linux.Connector: USBCable length: 1.5 metersDelivered with: USB GPS Antenna Beitian BN-82U.
Reference: QO100-OPA-BIAS-T1-760
This BT4G-based BIAS-TEE is used to power a LNA or a 10Ghz PLL LNB to receive the QO-100 / Es'Hail2 satellite.The BT4G covers the frequency bands from 30 MHz to 4 GHz. The +/- supply leads are
Reference: NOOELEC-100652-BALUN-HF-298
This balun is the perfect accessory to connect a long wire antenna, for example with the converter HF SDR Ham it Up to listen shortwave and HF bands from 0.5 to 30Mhz, but this balun can work up to
Reference: ANT-KIT-RTLSDR-598
VHF-UHF telescopic dipole antenna pack for SDR reception and with a flexible tripod and suction pad. This antenna set includes 1 dipole antenna support with 60cm of cable and with male SMA connector,
Reference: NAGOYA-RB16SP-SMA-F-529
Magnetic mount Nagoya RB-16-SP with antenna support connector in SMA male, for walkie-talkie to deport the antenna of the handheld (for example in car or at home).Coaxial cable: RG174 50 Ohms 3 meters
Reference: ADAPT-SMA-ATTENUA3-826
This adapter is a SMA attenuator available in version -3, -6, -10, -15, -20 or -30dB for frequencies from 0 to 6 Ghz.Connector end 1: SMA maleConnectique end 2: SMA femaleImpedance: 50 OhmsPower
Reference: NOO-SHIED-HACK-BLANC-100624-313
This RF shield Nooelec and component kit is specifically designed for HackRF One to eliminates EMI nearby. Comes with: RF shield, shield frame, shield cover, GND clip testpoint, J10, and a 20
Reference: ADAPT-SMA-CHARGE2-577
This connector is a male SMA terminator endowed with a dummy load 50 Ohms for a maximum power of 1 watt on frequencies from 0 to 6Ghz. Connectors end 1: SMA maleConnectors end 2: Dummy load 1W max
Reference: SPF5189Z-QO100-AL-LNA-833
This SPF5189Z LNA preamp improves reception performance from 50 Mhz to 4000 Mhz, based on SPF5189Z, with a noise factor of 0.6 dB and a maximum gain of approximately 20dB.This low noise amplifier is
Reference: GSG-BOITIER-TRANS-526
Great Scott Gadgets official case, transparent acrylic for the bare HackRF card One or to replace the black plastic case of HackRF. Case to assemble (instructions below). Delivered without HackRF.
Reference: VENTION-CHARGEUR-USB-859
Dual USB power charger with quick charge, 1 USB 2.0 port in 1A and 1 USB 2.0 port in 2.4A.USB output voltage: 5VVoltage input: 110V or 220V - EU plugUSB port: 1 USB 2.0 port in 2.4A (for tablet)USB
Reference: NANOVNA-PCB-DEMO-KIT2-1077
This NanoVNA RF demo kit is composed of a PCB to assemble, to perform tests or demonstration of RF integrated circuit (DIP) and SMT (SMT) components.Adapted to work with vector network analyzer
Reference: CABLE-COAXIAL-SMA-M-MCX-1M-306
Coaxial cable SMA Male to MCX Male with 50-ohms coaxial cable low loss KSR195 for use from 0 to 6GHz.Length: 1 or 5 metersConnector 1: SMA MaleConnector 2: MCX Male
Reference: CABLE-VENTION-VASA16-USB1-8501
Hi-Quality USB 2.0 Vention print cable Male A - Male B, high-speed.This cable is used to power a printer or scanner, as well as Upconverter HF Ham it up, SDR receiver SDRPlay: RSP1A, RSPdx or
Reference: XLA-PCB-ATTENUATEUR-1011
This RF attenuator module on PCB reduces the power of a radio signal from -10 to -30dB, with a maximum input power of 23dBm (200Mw), with female SMA connector, for use from 0 to 4000Mhz
Reference: ADAPT-RP-SMA-CHARGE3-579
This connector is a RP-SMA male terminator/termination endowed with a dummy load 50 Ohms for a maximum power of 1 watt on frequencies from 0 to 3Ghz. Connectors end 1: RP-SMA male (Reverse
Reference: XLA-SPLITTER-1010
This RF module allows you to separate a signal on 2 SMA outputs, with an attenuation of -6dB between the 2 outputs, for use from 0 to 5000Mhz (5Ghz).Supplied with: 1 2-channel RF RF Splitter module.
Reference: ADAPT-SMA-CHARGE1-576
This connector is a male SMA terminator/termination endowed with a dummy load 50 Ohms for a maximum power of 1 watt on frequencies from 0 to 3Ghz. Connectors end 1: SMA maleConnectors end 2: Dummy
Reference: ADAPT-BNC-CHARGE4-580
This connector is a male SMA terminator/termination endowed with a dummy load 50 Ohms for a maximum power of 1 watt on frequencies from 0 to 3Ghz. Connectors end 1: SMA maleConnectors end 2: Dummy
Reference: CROWD-PERF2+-687
PERF2+ is an electronic prototyping board designed for electronics enthusiasts and to make prototyping easier and faster. Perf2+ is a double-sided circuit board with perpendicular marks on each side.
Reference: CABLE-USB-OTG-432
USB OTG host cable adapter ompatible with Motorola Xoom, Samsung Galaxy S2/S3/S4/S5, Nokia N900/N810, and any other Micro USB devices with USB Host mode support features supported. - Connector Micro
Reference: WA5-PCB-MMIC-COAX-773
MMIC prototype circuit for connection with coaxial cable. Supplied without connector (coaxial soldering).This compact prototype board is compatible with more than 100 of the most popular MMIC
Reference: WA5-PCB-MMIC-SMA-774
MMIC prototype circuit on PCB for connection with SMA connectors (available as an option below).Supplied without SMA connector (solder).Fits standard SMA PCB connectors, including with SMA
Reference: ADAPT-RSP2-582
Connector for Hi-Z antenna of the SDRPlay receiver RSP2 and RSP2PRO. 5.08 female connector with 3 poles.
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal