Mounting bracket
Mounting bracket
Subcategories
Magnetic base
Car Mount
Duplexers/Triplexers
Our selection of duplexers and triplexers.
Antenna Switches
Our selection of antenna switches and coaxial HF switch 2, 3 and 4 ways.
149,00 € In stockReference: DIAMOND-CMF2000-1122
Diamond CMF-2000 common mode filter TVI RF choke
The Diamond CMF-2000 is a common mode filter that will prevent TVI and EMI CEM interference, caused by the transmission coaxial cable.Usable from 1 to 54 Mhz all bands, HF amateur radio, CB 27 Mhz,
149,00 €
139,00 € In stockReference: ALPHA-DELTA-SWITCH-4B-N-1216
4 position antenna switch with N female ALPHA DELTA 4B-N
Robust antenna switch ALPHA DELTA 4B-N 4 positions with N female connectors for frequency use from 0 to 1600 Mhz.With robust switch shaft and precision machined mechanism for stable switching
139,00 €
125,00 € In stockReference: ALPHA-DELTA-SWITCH-4B-PL-1215
4 position antenna switch with SO-239 (UHF-female) ALPHA DELTA 4B-PL
Robust antenna switch ALPHA DELTA 4B-PL 4 positions with SO-239 connectors (UHF-female) for frequency use from 0 to 500 Mhz.With robust switch shaft and precision machined mechanism for stable
125,00 €
115,00 € In stockReference: ALPHA-DELTA-SWITCH-2B-N-1214
2 position antenna switch with N female ALPHA DELTA 2B-N
Robust antenna switch ALPHA DELTA 2B-N 2 positions with N female connectors for frequency use from 0 to 1600 Mhz.With robust switch shaft and precision machined mechanism for stable switching
115,00 €
99,00 € In stockReference: ALPHA-DELTA-SWITCH-2B-PL-1213
2 position antenna switch with SO-239 (UHF-female) ALPHA DELTA 2B-PL
Robust antenna switch ALPHA DELTA 2B-PL 2 positions with SO-239 connector (UHF-female) for frequency use from 0 to 500 Mhz.With robust switch shaft and precision machined mechanism for stable
99,00 €
85,00 € In stockReference: DIAMOND-K9000-129
Diamond K9000 Motor drive mount antenna with remote
Diamond K9000 is a motorized mount antenna with remote control system and ability to adjust angle from 0 to 90 degrees in for 4 seconds! Designed to raise and lower HF/VHF/UHF mobile antennas that do
85,00 €
81,90 € In stockReference: KOM-MX-1300-PWR-C-1204
Triplexer 1.6-160 / 350-550 / 850-1300Mhz + Cables
Komunica Triplexer with cables:1.6-160MHz (PL)350-550MHz (N)850-1300MHz (N)In Connector: N female Impedance: 50 Ohm VSWR: < 1.2 - PL-259: 1.6-160MHz = 800W (PEP) / 0.20 dB
81,90 €
79,00 € In stockReference: KOM-MX-2000-PWR-N-1206
Triplexer 1.6 -60 / 110-170/350-570MHz, with cable
Triplexer 1.6 -60 / 110-170/350-570MHZ, with cables. Connector: SO-239 Connectors end cable: 2 x PL-259 + 1 N male - PL-259: 1.6-60MHz = 800W (PEP) - PL-259: 100-170MHz = 800W (PEP) - N male:
79,00 €
75,00 € In stockReference: DIAMOND-MX62N-612
Duplexer HF+50Mhz & VHF-UHF Diamond MX62-N & MX62-M
Duplexer Diamond MX62N and MX62M, Diamond Japan original warranty, covers from 1.6 to 56MHz for HF bands and from 120 to 470Mhz, in transmission and reception. The MX62N duplexer is perfect to use
75,00 €
69,00 € In stockReference: DIAMOND-K600-135
Heavy duty and design trunk mount antenna DIAMOND K600
Diamond K600M is a aerodynamic design trunk mount for heavy duty mobile antenna. Recommended for high-gain VHF/UHF antennas. FeaturesVertical adjustment range 0-9°Four set screwsStainless steel mount
69,00 €
69,00 € In stockReference: DIAMOND-K3000-147
Strong 3-point Magnet Antenna Base Diamond K-3000
Strong 3-point Magnet Antenna Base Diamond K3000. Antenna specification for K-3000 Length of antenna: Less than 1.85mWeight:Less than 1.1kg (If the antennas have the loading coil, the coils should be
69,00 €
67,00 € In stockReference: DIAMOND-SX27P-397
Handheld SWR & Power Meter VHF UHF 60W
SWR-meter and watt meter portable, original Diamond SX-27P for VHF bands from 140 to 150MHz and UHF band from 430 to 450MHz, it can measure the SWR and power (60 watts maximum). Operating
67,00 €
65,00 € In stockReference: DIAMOND-MGC50-144
Window through SO-239 cable set Diamond MGC50
Diamond MGC50 is a window through SO-239 cable set. Length:50cm (Between connectors)Weight:102g Freq.: 0 to 1500MHz
65,00 €
65,00 € Out of stock, available soonReference: COMET-CF416A-987
Combiner/Splitter COMET CF-416 A and B
COMET CF-416 duplexer / combiner / splitter, to separate HF/VHF frequencies from 1.3 to 170 Mhz and UHF band 350 to 540 Mhz.Available in 2 versions with PL-259 or N connectors for the UHF band. The
65,00 €
64,80 € In stockReference: KOM-MX-620-PWR-M-1208
Duplexer 1.6-56 & 140-470MHz, with cable
Duplexer 1.6-56 Mhz (HF+6m) & 140-470MHz (VHF+UHF), with cable. Connector: SO-239 Cable Connectors: 2 x PL-259 - PL-259: 1.6-56MHz - 600W (PEP) - PL-259: 140-470MHz - 600W (PEP)
64,80 €
59,00 €Reference: DIAMOND-K33
Tilt angle adjustable mount bracket 4-door car Diamond K33
Diamond K33 tilt angle adjustable mount bracket for heavy duty type. Coaxial cable with SO-239 socket (UHF female) compatible: Diamond RG3MR or RG6MR, SO-239 Nagoya socket cable.
59,00 €
53,50 € In stockReference: KOM-MX-720-PWR-N-1210
Duplexer 1.6-150 Mhz & 400-470MHz with cable
Duplexer 1.6-150 & 400-470MHz, with low loss cable. Connecteur: SO-239 Connecteurs: 1 x PL-259 + 1 N mâle - SO-239: 1,6-30MHz = 1KW (PEP) / 50-150MHz = 400W (PEP) - N mâle: 400-460Mhz = 240W (PEP)
53,50 €
49,90 € Out of stock, available under 10-15 daysReference: DIAMOND-MCRMBNC-1036
Magnet BNC base bracket Diamond MCR-M BNC
Diamond MCRMBNC is a magnet base bracket for handheld transceivers and any devices with BNC connector. Coaxial cable: RG58 2.5m Connector: BNC Male / BNC FemaleMagnet diameter: 53mm
49,90 €
49,90 € Out of stockReference: DIAMOND-MCRMSMA-142
Magnet SMA base bracket
Diamond MCRMSMA is a magnet base bracket for handheld transceivers and any devices with SMA connector. Coaxial cable: RG58 2.5m Connector: SMA Male / SMA FemaleMagnet diameter: 53mm
49,90 €
49,50 € In stockReference: KOM-PWR-SW2N-1197
2 position antenna switch with N plug
Commutateur d'antenne 2 positions avec connecteur fiche N femelle. Pour utilisation en fréquence de 0 à 3000 Mhz (3 Ghz).
49,50 €
48,90 € In stockReference: KOM-MX-600-PWR-N-1207
Duplexer 1.6-150Mhz / 400-460MHz N connectors
Komunica duplexer. Frequency Range: 1.6-150MHz N female 400-460MHz N female IN connector: N female
48,90 €
45,90 € In stockReference: DIAMOND-MRX-141
Magnet BNC base bracket Diamond MRX
Diamond MRX is a magnet base bracket for handheld transceivers and any devices with BNC connector. Coaxial cable: RG58 3m Connector: BNC Male / BNC FemaleMagnet diameter: 76.5mm
45,90 €
45,90 € In stockReference: DIAMOND-MX72H-146
HF VHF UHF Duplexer DIAMOND-MX72H
HF VHF UHF Duplexer Diamond MX72H.
45,90 €
45,90 € In stockReference: KOM-MX-720-PWR-D-1209
Duplexer 1.6-150 Mhz & 400-460MHz with SO-239
Duplexer 1.6-150 & 400-460MHz, without cable. Connector: SO-239 Connectors: 2 x SO-239 - SO-239: 1.6-30MHz = 1KW (PEP) / 50-150MHz = 400W (PEP) - SO-239: 400-460Mhz = 240W (PEP)
45,90 €
45,50 € Out of stock, available in 2 to 3 weeksReference: KOM-PWR-SW2M-1196
2 position antenna switch with SO-239 (UHF-female)
Commutateur switch d'antenne 2 positions avec connecteur SO-239 (UHF-femelle). Pour utilisation en fréquence de 0 à 1000 Mhz (1Ghz).
45,50 €
39,90 € Out of stock, available in 2 weeksReference: DIAMOND-K512-132
Roofrail mount bracket 3-axis adjustable K-512 Diamond
K-512 Diamond Roofrail Mounting Bracket 3-axis adjustable. Mast diameter accepted: 15-34mmRooftop railing Height accepted: Less than 32mm Width accepted: I 50mmSquare mast side length accepted:
39,90 €
39,90 € In stockReference: DIAMOND-K550-1121
Support 2 adjustable axes large car gallery DIAMOND-K550
2-axis swivel antenna mounting bracket, Diamond K500 and K550L for car roof rack and racks with large sections.Available in 2 versions:K550 for bars less than 50mm wideK550L for bars less than 75mm
39,90 €
39,90 € In stockReference: DIAMOND-K44L-128
Car gallery antenna support Diamond K44L
Diamond K44L support for mounting a mobile antenna on a car's roof rack or a 1.5cm to 4cm tube.Support with adjustable tilt angle.Diameter accepted: 15mm to 40mm Coaxial cable with SO-239 socket (UHF
39,90 €Reference: LIVRE-2021-WRTH-1123
WRTH 2021 - World Radio TV Handbook 75th edition
The World Radio TV Handbook 75th edition, WRTH 2021 is the most accurate and complete directory in the world of broadcasting stations, with 672 pages it is a reference since 1947 in the world of
39,00 € 45,00 €Online only
37,90 € In stockReference: DIAMOND-BU50A-517
Balun 1:1 HF 1.7Mhz à 40Mhz Diamond BU50/A
Diamond BU50/A balun 1:1, genuine, operates from 1.7 to 40Mhz and allows to receive and transmit on HF bands.Technical data sheet of the HF BU50A balun:● Operating frequency from 1.7 to 40MHz●
37,90 €
35,90 € Out of stock, available in 10-15 daysReference: F1OPA-WIDEBAND-LNA3-805
LNA Wide Band 50-2500Mhz amplifier F1OPA
Wide-band LNA preamp, based on PGA-103+, to improve reception performance from 50 Mhz to 1500 Mhz, with a maximum gain of 20-24dB and a noise factor of 0.4dB.This VHF-UHF LNA offers a very good
35,90 €Online only
29,95 € In stockReference: DIAMOND-MAT50-625
Ground plane for magnetic mount & HF antenna Diamond MAT50
To use an HF antenna below 50Mhz band, a ground plane are required. This is not always possible or easy especially for antennas with magnetic base or for installations on a balcony. Diamond MAT-50
29,95 €
29,90 € Out of stock, available soonReference: DIAMOND-RG6MR-RG58U-269
Coaxial cable RG58 6m with SO-239 socket (UHF female) Diamond RG-6MR
The cable antenna RG6MR Diamond is a length of 6 meters and allows you to connect an antenna with base PL259 (male UHF) on the SO239 socket (UHF female). It is equipped with a SO239 and RG58U cable
29,90 €
29,90 € In stockReference: DIAMOND-KLR-939
Rooftop railing mount bracket KLR for K9000
Diamond KLR mounting bracket for attaching to a car gallery the mount for the Diamond K9000 motorized moving antenna.
29,90 €
29,90 € In stockReference: SIRIO-EMBASE-MAG145-371
SIRIO 125mm magnetic base with RG58 and PL-259 coaxial cable
This 12.5cm diameter SIRIO magnetic base allows a PL-259 (UHF-male) antenna to be screwed to place on a car roof or any metal surface of at least 1m².The magnetic base can support large antennas over
29,90 €
29,90 € In stockReference: MINIVNA-CALIBRATION-727
SMA Calibration Kit with 50 Ohm dummy load for MiniVNA NanoVNA & VNA
This calibration kit can be used with any SMA connector device, such as the MiniVNA Tiny and PRO2 or NanoVNA and any VNA.The SMA calibration kit consists of a dummy load of 50 ohms, an open circuit
29,90 €
29,50 € Out of stock, available 7-10 daysReference: WIMO-CABLE-EMBASE-SO239-954
Coaxial cable with SO239 base for drilling
Base for drilling support, with SO239 connector (female UHF) for screwing the antenna.The 6mm RG58U 50ohms cable is 4 meters long and has a PL259 (UHF Female) connector at its end.
29,50 €Reference: DIAMOND-HRK-134
Adhesive backed mount for flat surface & glass
Adhesive backed Diamond HRK for flat surface installations including glass, fiberglass, and metal. Can be used on the body of a car for an antenna less than 1m long.
29,00 €
28,90 € In stockReference: KOM-EMBASE-MAG2-BK1600-1000
Magnetic mount 160mm BK-1400 with cable PL259
Magnetic base of 16cm in diameter for screwing a PL-259 antenna (UHF-male) to land on a car roof or any 1m² minimum metal surface. The BK1600 magnetic base from CRT France, allows support of large
28,90 €
28,50 € In stockReference: DIAMOND-BK11-266
Balcony railing bracket for antenna Diamond BK11
The BK11 (former BK10) is a mounting bracket to put for example a mobile antenna on a balcony. This support agree to the antenna sockets standard PL (UHF male) or plug N and can be mounted directly on
28,50 €
27,90 € In stockReference: DIAMOND-BU55-538
Balun 1:1 HF+6M from 3 to 75Mhz Diamond BU55
Genuine Diamond BU55 balun 1:1, operates from 3 to 75Mhz, allows to receive and transmit on HF bands + 6 meters (50Mhz).Technical data sheet of the HF BU55 balun:● Operating frequency from 3 to 75MHz●
27,90 €
27,50 € In stockReference: DIAMOND-RG3MR-3M-362
Coaxial cable RG58 3m with SO-239 socket (UHF female) Diamond RG-3MR
The cable antenna RG3MR Diamond is a length of 3 meters and allows you to connect an antenna with base PL259 (male UHF) on the SO239 socket (UHF female). It is equipped with a SO239 and RG58U cable
27,50 €
25,90 € In stockReference: DIAMOND-KTH-130
Hatchback mount KTH bracket for Diamond K9000
Mounting bracket Diamond KTH for trunk lid, hatchback or gate for motorized antenna Diamond K9000.
25,90 €
25,90 € In stockReference: DIAMOND-KRR
Rooftop railing KRR mount bracket for Diamond K9000
KRR Rooftop railing mount bracket for motorized antenna Diamond K9000.
25,90 €
25,90 € In stockReference: DIAMOND-KRS-160
Roofside gutter KRS mount bracket for Diamond K9000
Diamond KRS Roofside Gutter Mount Bracket for motorized antenna Diamond K9000.
25,90 €
24,90 € In stockReference: KOM-EMBASE-MAG3-BM1PL-1001
Strong magnetic base BM-1-PL 120mm with 5m cable PL259
Strong magnetic base mount of 12cm in diameter for screwing a PL-259 antenna (UHF-male) to land on a car roof or any 1m² minimum metal surface. The BM-1-PL Komunica magnetic base, allows support of
24,90 €
22,90 € In stockReference: KOM-EMBASE-BK-1500-539
Magnetic base 150mm with coaxial cable RG58 and PL-259
This 15cm diameter magnetic base ensures a solid fixation and allows to screw a PL-259 antenna (UHF-male) on a car roof or a metal surface of minimum 1m².The magnetic base allows to support antennas
22,90 €
22,90 € Out of stock, available in 2 to 3 weeksReference: KOM-BK-700-SMA-1172
Magnetic Base 7cm for antennas with SMA male connector
Flat magnetic base with a diameter of 7cm and to offset an antenna with a SMA male connector.Base connector : SMA femaleCoaxial cable connector : SMA femaleHigh magnetic adhesionDiamter magnet: 7cm5m
22,90 €
22,90 € In stockReference: KOM-BK-700-SMAF-1173
Magnetic base 7cm for antenna with SMA female connector
Flat magnetic base with a diameter of 7cm and to offset an antenna with a SMA female connector.Base connector : SMA maleCoaxial cable connector : SMA MaleHigh magnetic adhesion5m RG-58 coaxial cable
22,90 €
19,00 € Out of stock available soonReference: CRT-SWR2-571
SWR & Power Meter 26-30Mhz 10-100W CRT
SWR-Meter and watt-meter for the 27Mhz citizen band and frequencies from 26 to 30 Mhz, allows to measure the ROS (SWR) of the antenna and the power (100 watts maximum). Frequency: 26 to 30MHzPower
19,00 €
18,90 € In stockReference: NAGOYA-RB500-1067
Nagoya RB-500 3 axis trunk lid universal antenna mount 4-door car
Nagoya RB-500 universal support for mounting a mobile antenna on a 4-door car, to be installed on a car trunk or trunk lid.Adjustable and adjustable according to 3 axis.Supplied with: Nagoya RB-500
18,90 €
18,90 € In stockReference: NAGOYA-RB600-1068
Nagoya RB-600 hatchback 3 axis universal antenna mount 5-door car
Nagoya RB-600 universal support for mounting a mobile antenna on a 5-door car, to be installed on hatchback car. Adjustable and adjustable according to 3 axis.Supplied with: Nagoya RB-600 hatchback
18,90 €
17,90 € In stockReference: NAGOYA-SUPPORT-RB56-870
Nagoya Nagoya RB56 chrome bracket for car gutter
Nagoya RB56 mount bracket for mounting a mobile antenna on a car gutter. 1 angle adjustable.Come with: 1 Nagoya RB56 genuine mount bracket, without cable (optional below). Coaxial cable with SO-239
17,90 €
16,90 € In stockReference: NAGOYA-RB400-138
Nagoya RB-400 trunk lid universal antenna mount 4-door car
Nagoya RB-400 antenna support for mounting a mobile antenna, to mount on trunk lid, 4-door car. 2 angle adjustable.Delivered: Nagoya support RB-100 genuine, without cable (optional below). Coaxial
16,90 €
16,90 € In stockReference: NAGOYA-RB700-1070
Nagoya RB-700 hatchback 2 axis universal antenna mount 5-door car
Nagoya RB-700 genuine universal support for mounting a mobile antenna on a 5-door car, to be installed on hatchback car. Adjustable and adjustable according to 2 angles.Supplied with: Nagoya RB-700
16,90 €Reference: NAGOYA-RBCLPSP-SMAF-530
Window mount Nagoya for walkie-talkie antenna
This Nagoya mounting bracket allows to deport a walkie-talkie antenna to fix it on a window car. Antenna support connector: SMA Male Antenna cable connector: SMA Female, SMA male or BNC Male (to
15,72 € 18,50 € -15%
14,50 € In stockReference: NAGOYA-RB16SP-SMA-F-529
Magnet Nagoya RB-16-SP base bracket mount SMA-M / SMA-F / BNC
Magnetic mount Nagoya RB-16-SP with antenna support connector in SMA male, for walkie-talkie to deport the antenna of the handheld (for example in car or at home).Coaxial cable: RG174 50 Ohms 3 meters
14,50 €
14,50 € In stockReference: NAGOYA-RB16-BNC-1066
Nagoya RB-16 BNC male / female magnetic base + coaxial cable
Nagoya RB-16 magnetic base with female BNC antenna support connector, with male BNC connector coaxial cable.For example, allows the BNC antenna of a walkie-talkie to be moved to the roof of a car to
14,50 €
13,90 € In stockReference: NAGOYA-COAX-RG58-4M-534
4m antenna cable with SO239
The cable is a length of 4 meters and allows you to connect an antenna with base PL259 (male UHF) on the SO239 socket (UHF female). It is equipped with a SO239 and RG58 50ohms cable and the other
13,90 €
11,90 € In stockReference: NAGOYA-RB20B-148
Mini Hatchback car Door Mount Nagoya RB-20B
Mini Nagoya RB-20B Hatchback Door, trunk lid mount Antenna Bracket. Shipped with: 1 Nagoya RB-20B genuine, without cable (in option below). Coaxial cable with SO-239 socket (UHF female) compatible:
11,90 €
10,90 € In stockReference: ADAPT-DIAMOND-BNCPSMAJ-257
BNC Male to SMA female RF Adapter for handheld
Adapter for walkie-talkie, handheld VHF-UHF or scanner equipped BNC to use SMA antennas.- The adapter has a BNC Male connector on one side and the other is SMA Female- The design is specially adapted
10,90 €
10,90 € In stockReference: ADAPT-DIAMOND-SMAJSMAJ-276
SMA to SMA RF adapter for handheld
Adapter for walkie-talkie, handheld VHF-UHF or scanner equipped SMA to use SMA antennas.- The adapter has a SMA Female connector on one side and the other is SMA Female- The design is specially
10,90 €
9,90 € In stockReference: ADAPT-SMA-CHARGE2-577
SMA Male Terminator 6Ghz dummy load 1W
This connector is a male SMA terminator endowed with a dummy load 50 Ohms for a maximum power of 1 watt on frequencies from 0 to 6Ghz. Connectors end 1: SMA maleConnectors end 2: Dummy load 1W max
9,90 €
9,90 € In stockReference: SIRIO-SUPPORT-M1-657
Stainless steel mounting bracket for antenna SIRIO M-1
Stainless steel mounting bracket SIRIO M-1. Allows the installation of mobile or portable antenna. Size: 3,8 x 6,4 x 9,9 cm. Delivered with: 1 bracket only SIRIO M-1, without base or coaxial cable
9,90 €
9,90 € In stockReference: ADAPT-SMA-ATTENUA3-826
RF attenuator SMA 0-6 Ghz from -3 to -30dB 2W
This adapter is a SMA attenuator available in version -3, -6, -10, -15, -20 or -30dB for frequencies from 0 to 6 Ghz.Connector end 1: SMA maleConnectique end 2: SMA femaleImpedance: 50 OhmsPower
9,90 €
7,90 € Out of stockReference: CRT-CORDON-BNC-90CM-444
Cord PL-PL-259 50cm RG58 50 ohms
BNC-BNC cable 90 centimeters with 6mm RG58 coaxial cable 50 ohm and 2 BNC-Male connectors assembled.
7,90 €
7,20 € In stockReference: MIDLAND-SP21-639
Mirror mount for mobile antenna
Mounting bracket for mirror or metal rod. Allows the installation of any mobile type antenna. Delivered with: 1 bracket only, without base or coaxial cable (optional)
7,20 €
5,50 € In stockReference: ADAPT-SMA-M-BNC-F2-275
SMA to BNC RF adapter for handheld
RF adapter for walkie-talkie, handheld VHF-UHF or scanner, equipped with SMA female connector and to use a BNC male antenna. - The adapter is equipped with an SMA Male connector on one side and the
5,50 €
5,40 € In stockReference: ADAPT-RP-SMA-CHARGE3-579
RP-SMA Male Terminator 3Ghz dummy load 1W
This connector is a RP-SMA male terminator/termination endowed with a dummy load 50 Ohms for a maximum power of 1 watt on frequencies from 0 to 3Ghz. Connectors end 1: RP-SMA male (Reverse
5,40 €
5,40 € In stockReference: ADAPT-SMA-CHARGE1-576
SMA Male Terminator 3Ghz dummy load 1W
This connector is a male SMA terminator/termination endowed with a dummy load 50 Ohms for a maximum power of 1 watt on frequencies from 0 to 3Ghz. Connectors end 1: SMA maleConnectors end 2: Dummy
5,40 €
3,95 € In stockReference: ADAPT-BNC-CHARGE4-580
SMA Male Terminator 3Ghz dummy load 1W
This connector is a male SMA terminator/termination endowed with a dummy load 50 Ohms for a maximum power of 1 watt on frequencies from 0 to 3Ghz. Connectors end 1: SMA maleConnectors end 2: Dummy
3,95 €
2,00 € In stockReference: CABLE-VENTION-VELCRO-KAABA-852
Velcro scratch cable tie 1, 2 or 5m Vention
Velcro cable tie (to cut) to attach any type of cable. Width: 11mm and available length: 1m, 2m or 5m (to choose below)Delivered with: 1 Vention Velcro cable tie.
2,00 €
1,95 € In stockReference: NAGOYA-UHFPU213-PL259-11MM-375
PL-259 connector 11mm (UHF male)
PL259 long socket connector (UHF male) for coaxial cable 11mm weld.
1,95 €
1,95 € In stockReference: SIRIO-DV-SCREW-BOLT-CHROME-1257
Sirio screw and bolt DV mounting Chrome
Screw and bolt, chrome, for Sirio antennas with DV mount (DV-Mount).
1,95 €
1,50 € In stockReference: NAGOYA-UHFPU58-PL259-6MM-374
PL259 connector Teflon 6mm (UHF male)
PL259 short socket connector (UHF male) for coaxial cable 6mm weld. Other model available: PL 259 6mm in teflon.
1,50 €Reference: WA5-PCB-MMIC-COAX-773
MMIC prototype circuit PCB board for coaxial
MMIC prototype circuit for connection with coaxial cable. Supplied without connector (coaxial soldering).This compact prototype board is compatible with more than 100 of the most popular MMIC
1,47 € 2,95 € -50%
1,00 € In stockReference: ADAPT-RSP2-582
Connector Hi-Z for SDRPlay RSP2 & PRO
Connector for Hi-Z antenna of the SDRPlay receiver RSP2 and RSP2PRO. 5.08 female connector with 3 poles.
1,00 €
0,95 € In stockReference: NAGOYA-BOUCHON-SO239-535
Plastic protective cover SO239 (UHF Female)
Plastic plug for SO239 base (female UHF).
0,95 €
Delivery Europe & Overseas
Stock and shipped from France
Product return
14 days to return, 2 warranty
Email support
Response within 24h to 72h
Secure payment
SSL, VISA, Mastercard, Paypal