Clear Acrylic Case for HackRF One by GSG

Great Scott Gadgets official case, transparent acrylic for the bare HackRF card One or to replace the black plastic case of HackRF.

Case to assemble (instructions below).

Delivered without HackRF.

More details

More info

Assembly Instructions

Warning: Do not overtighten! Hand-tighten only at every step.

1 - Use the guitar pick supplied to extract the HackRF One circuit board from the black plastic case.
2 - Insert one long screw into each corner of the bottom acrylic panel. Secure each long screw with a short (5 mm) spacer on the opposite side of the panel.
3 - Place the HackRF One circuit board (facing up) on top of the bottom panel, fitting the ends of the long screws through the corner mounting holes of the circuit board.
4 - Secure the circuit board with one long (6 mm) spacer in each corner.
5 - Place the top acrylic panel on top of the circuit board, aligning the cutouts with the circuit board's expansion headers.
6 - Secure each corner with a short screw.

Accessories

Ham it Up 1.3 & 1.3+ Converter HF 0.5-50Mhz Nooelec
Nooelec's Ham It Up v1.3 is an up-converter HF, equipped with the 125Mhz filter soldered on the PCB and allows to listen to all MF / HF bands from 0.5 to 50 Mhz, in all modes of modulation, from a
48,00 €
In stock
ANT500 SDR ADSB antenna 75-1000Mhz SMA-M
Telescopic antenna ANT500, VHF-UHF 50 ohms designed to operate in RX from 75 MHz to 1 GHz. Configurable length of 20 cm to 88 cm. Stainless steel SMA male connector and elbow swivel 360 °. This is an
32,90 €
In stock
Diamond antenna SRH-789 SMA-M 95-1100Mz + TX 144/430Mhz
Dual band directional antenna Original Diamond SRH-789 with SMA Male connector, for receiving and transmitting on VHF-UHF bands (144/430 MHz) and reception on aviation bands 120/150/300/450/800 MHz
29,90 €
In stock
LNA VHF UHF preamplifier with PGA-103 + for RF and SDR application
The LNA4ALL is a pre-amplifier and a low-pass filter (LNA) with SMA female RF connectors and for RF frequencies covering all bands from 28MHZ to 2500 MHz. It improves greatly reception performance, on
LNA preamp with BIAS-T for HackRF Airspy SDRPlay
Preamplifier and LNA (low noise amplifier) specially adapted with BIAS-T for HackRF One, AirSpy, SDRPlay and RTL-SDR V3 usb stick. It highly increases the reception performance (+ 11dB to + 23dB) and
USB VFO jog Shuttle Xpress Contour Design for SDR
Allows to control by USB the change of frequencies of an SDR software and to get a classic operation of a VFO on a radio hardware SDR!Fully configurable with the supplied software, Shuttle Xpress is
53,00 €
Out of stock, available 5-7 days
Nooelec RF Shield Kit for HackRF One
This RF shield Nooelec and component kit is specifically designed for HackRF One to eliminates EMI nearby. Comes with: RF shield, shield frame, shield cover, GND clip testpoint, J10, and a 20
9,90 €
In stock
Aluminium case HackRF One - Nooelec
Nooelec aluminium case V2 (new version) specifically designed for HackRF One reduce parasitic interference nearby and add a stronger resistant case. This aluminum case is for replacing the original
34,90 €
In stock
Antenna ANT700 300-1100Mhz SDR VHF UHF ADSB
Telescopic Antenna ANT700 from 300 to 1100 MHz, made by Great Scott Gadgets. The total length of the antenna ANT700 is configurable from 9.5 cm to 24.5 cm. The ANT700 is constructed of stainless
28,90 €
In stock