Our store uses its own and third-party cookies to improve our services, secure transactions and enable tracking. To give your consent to its use, press the Accept button or choose Cookies.
Please note that refusing the Paypal cookie will prevent this payment method from being displayed and working in our store.
Viewed products
The NMRF filter is a bandpass filter centered...
The NMRF filter is a bandpass filter centered on 2450Mhz with a bandwidth of 150Mhz, for use in frequency from 2400 to 2500Mhz with a maximum power of 10W, for radio applications: Wifi, Zigbee, Drone and the radio amateur QO100 satellite .
Connector 1: SMA Male
Connector 2: SMA Female
This filter is particularly recommended when using a WIFI amplifier to suppress parasitic and harmonic frequencies.
Supplied with: 1 NMRF FBP-2400 Mhz filter.
Optimal frequency range: 2400 - 2500 MHz
Center frequency: 2450 MHz
Bandwidth: 150Mhz
Impedance: 50 Ohms
Maximum power: 10W
Insertion loss: <2dB @ 2400 MHz
Connector 1: SMA Male (to the TX or the amp)
Connector 2: SMA Female (to the antenna)
Dimensions: 34.3 x 17.5mm
Rohs Standards
This RF adapter converts a RP-SMA male connector to a SMA Male connector. Beware this adapter is a Reverse SMA (RP), it is mainly used in WIFI application.
2,85 €tax excl.
3,80 € -10%This RF adapter converts a RP-SMA Female connector to a SMA Female connector. Beware this adapter is a Reverse SMA (RP). It is mainly used in WIFI connections.
3,71 €tax excl.
4,95 € -10%This RF adapter converts a RP-SMA Female connector to a SMA Male connector. Suits for WIFI devices and application. Beware this adapter is a Reverse SMA (RP). It is mainly used in WIFI connections.
3,38 €tax excl.
4,50 € -10%This RF adapter converts a RP-SMA male connector to a SMA Female connector. Suits for WIFI devices and application. Beware this adapter is a Reverse SMA (RP). It is mainly used in WIFI connections.
3,38 €tax excl.
4,50 € -10%Adaptateur pigtail RP-SMA (reverse SMA) Female to N Female.
7,43 €tax excl.
9,90 € -10%Printed circuit PCB wifi antenna WA5VJB Quad Patch for 2.4Ghz with a gain of 12dBi.The antenna is delivered without connector (solder wire).Frequencies: 2400-2480 MHz (WIFI 2.4 Ghz)Type: Patch
17,10 €tax excl.
21,60 € -5%The Analog Devices CN0417 is a small RF power amplifier, powered by micro-USB, optimized to operate on 2400 MHz with 100mW max, gain of 20-21dB max., with a integrated bandpass filter 2400 to
45,83 €tax excl.
WA5VJB single patch antenna for 2.4Ghz with left circular LHCP or right circular RHCP polarization and 6dBi gain.This antenna is compatible for use in 2400Mhz transmission on the narrow transponder
9,90 €tax excl.
12,50 € -5%This bandpass filter for the 2.4 Ghz (13cm) allows to reject the local oscillator and harmonics frequencies of the Up-Converter for QO-100 to get a clean signal on the satellite, with a max. input
21,58 €tax excl.
This power amplifier equipment with a gain of 30dB is intended to operate primarily with F1OPA's upconverter 144 / 432Mhz - 2400 MHz to traffic on the QO-100 satellite uplink with 100mW output (20dBm)
41,67 €tax excl.
The Taoglas Airvu 2.4Ghz bandpass filter is a 100Mhz broadband filter, for use in frequency from 2400 to 2500Mhz and a maximum power of 10W.Connector 1: RP-SMA MaleConnector 2: RP-SMA Female Note: The
24,08 €tax excl.
Very low loss coaxial cable with SMA Male connector on each end, for example to connect a 2.4Ghz amplifier to a transverter for OQ-100, or any use requiring a very low loss cable like the
4,50 €tax excl.
6,00 € -10%Very low loss RG402 coaxial cable with straight SMA Male and angled SMA Male, for example to connect a 2400 Mhz amplifier to a converter OQ-100, or any use requiring a very low loss cable. Coaxial
4,88 €tax excl.
6,50 € -10%Very low loss RG-402 coaxial cable with angled SMA Male on both side, 50 ohms and with a length of 10cm. Note: This rigid cable can be bent but once installed in its position of use, the cable must
5,25 €tax excl.
7,00 € -10%This RG402 coaxial cable converts a RP-SMA male connector to a SMA Male connector. Suits for example for WIFI devices and application. Beware this adapter is a Reverse SMA (RP). Note: This cable is
4,50 €tax excl.
6,00 € -10%The NanoVNA V2 SAA2N is an antenna and vector network (VNA) analyzer that covers the HF, VHF and UHF bands from 50 KHz to 3000 MHz, with N or SMA type connector and a metal case.It measures the
Variable gain pre-amplifier with 15dBGain control in 1 dB stepsAdditional filtering for the 2.4 GHz bandPower supply 8-30 V DCOutput detector This equipment is intended for amateur radio use only on
35,42 €tax excl.
Click here to leave a review
Be the first to ask a question about this product!
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal