Diamond CMF-2000 common mode filter TVI RF choke

The Diamond CMF-2000 is a common mode filter that will prevent TVI and EMI CEM interference, caused by the transmission coaxial cable.

Usable from 1 to 54 Mhz all bands, HF amateur radio, CB 27 Mhz, 50Mhz (6m) with a maximum admissible power of 2000W.

Connects to the transmission line via female UHF connectors (SO-239) and act like a RF choke line isolator.

This low pass filter eliminates harmonic frequencies outside the 1-54Mhz band.

Comes with: 1 Diamond CMF-2000, original warranty.

More details

Data sheet

CMF2000 RF choke filter specifications

Frequency: 1 MHz to 54 MHz
Maximum input power: 2000W (SSB)
Common mode attenuation: -50dB or more
Insertion loss: less than 0.2dB
Impedance: 50Ω
VSWR: Less than 1.2
Connector: UHF female (SO-239)
Total length: 380 mm
Weight: 650g

Accessories

LNA & SAW filter for Inmarsat and Outernet
This LNA and SAW filter from Nooelec is specially designed to operate on 1.5Ghz Outernet frequency band and for Inmarsat radio applications, covering from 1.50GHz to 1.58GHz. It significantly
29,90 €
In stock
Broadcast FM Band Cut filter by RTL-SDR.com
This band-cut filter is design by RTL-SDR.com, it blocks and reject broadcast FM band between 88 to 108 MHz with over 50dB of attenuation. Insertion loss is less than 0.5 dB between 0-1 GHz, and less
19,90 €
In stock
Broadcast AM Band Cut filter by RTL-SDR.com
This high-pass notch filter is designed by RTL-SDR.com and rejects the AM broadcast from 500 kHz to 1.7 MHz, with attenuation of more than 50dB. In fact, because of the attenuation, the filter is
19,90 €
In stock
Ground plane for magnetic mount & HF antenna Diamond MAT50
To use an HF antenna below 50Mhz band, a ground plane are required. This is not always possible or easy especially for antennas with magnetic base or for installations on a balcony. Diamond MAT-50
28,45 € 29,95 € -5%
Out of stock, available 5 march 2018 (Diamond delay)
1090 Mhz SAW Bandpass ADS-B filter F1OPA
This band-pass / bandstop ADS-B filter for the 1090Mhz improves ADSB receive performance and suppresses signals outside the 1090Mhz band.Delivered with: 1 F1OPA 1090Mhz SAW Bandpass Filter.
26,90 €
In stock
2.4 Ghz SAW Bandpass filter for QO100
This bandpass filter for the 2.4 Ghz (13cm) allows to reject the local oscillator and harmonics frequencies of the Up-Converter for QO-100 to get a clean signal on the satellite, with a max. input
25,90 €
In stock
Bandpass SAW Filter 868 Mhz for Helium LoRa Lorawan SigFox
This filter for the 868 MHz bandpass allows to improve the selectivity of the reception and to suppress the parasitic signals outside the 868MHz band and in particular to reject the GSM 900 MHz
27,90 €
Out of stock, available in 1 month
TAOGLAS RF Filter Bandpass 2.4Ghz 10W WiFi and QO-100 - BPF.24.01
The Taoglas Airvu 2.4Ghz bandpass filter is a 100Mhz broadband filter, for use in frequency from 2400 to 2500Mhz and a maximum power of 10W.Connector 1: RP-SMA MaleConnector 2: RP-SMA Female Note: The
35,90 €
In stock
Pass-Band Filter 2400 Mhz 10W WiFi Zigbee QO100
The NMRF filter is a bandpass filter centered on 2450Mhz with a bandwidth of 150Mhz, for use in frequency from 2400 to 2500Mhz with a maximum power of 10W, for radio applications: Wifi, Zigbee, Drone
39,90 €
Out of stock
Bandpass filter 1090 Mhz ADS-B AirNav RadarBox
This 1090 Mhz ADS-B bandpass / band-stop filter to improve ADS-B reception performance and suppress parasitic signals outside the 1090Mhz band. With SMA male and SMA female connector. Compatible with
29,90 €
In stock
137 Mhz filter Double LNA & SAW Nooelec for NOAA
This SawBird + filter from Nooelec is specially designed to operate on the NOAA 137 Mhz frequency band and for NOAA weather satellite reception applications.It makes it possible to significantly
44,90 €
In stock