Wide-band LNA preamp, based on PGA-103+, to improve reception performance from 50 Mhz to 1500 Mhz, with a maximum gain of 20-24dB and a noise factor of 0.4dB.
This VHF-UHF LNA offers a very good compromise between low noise, gain and wide frequency band and can operate in emission as amplifier from 50 to 2500Mhz.
With ESD protection against electrostatic discharge, LED indicator for powering up. Power by Bias-Tee or external (8-14V).
Comes with: 1 LNA WIDEBAND OPA-Design.
Data sheet wideband LNA OPA DESIGN 425.96k
Frequency of use in RX: 50 Mhz to 1500 Mhz
Gain: 20-24 dB VHF-UHF
Gain @ 144MHz: 24.4dB
Gain @ 432 MHz: 20.8dB
Gain @ 1296MHz: 13.2dB
Gain @ 2400MHz: 8.1dB
Frequency of use in TX: 50 Mhz to 2500 Mhz
Max input power: +13dBm - 20mW
Max output power : +20dBm - 100mW
Noise factor: ~ 0.4 dB
DC power supply: 8 to 14V
Consumption: 70 mA
Dimensions: 40 x 30 (excluding SMA connector)
Amateur Radio Design: F1OPA
2 years warranty*
* The warranty does not cover the PA and the loss of power, which may result from an assembly error, an incorrect antenna adjustment (ROS), a maximum input power not respected, a short -circuit of the power supply or the coaxial line and the damage linked to electrostatic discharges.
Pigtail RF adapter SMA Male to SMA Male to connect for example a converter Ham it up to a HackRF One, or SDRPlay, and any device with a SMA female connector. Coaxial cable RG 316 50 ohms. Available in
The LNA HF from F1OPA is a pre-amplifier and a low-pass filter (LNA), very powerful (+18dB to +20dB), with SMA Female connectors, for HF frequencies and short waves from 500 kHz to 30 MHz, with
The LNA4ALL is a pre-amplifier and a low-pass filter (LNA) with SMA female RF connectors and for RF frequencies covering all bands from 28MHZ to 2500 MHz. It improves greatly reception performance, on
Preamplifier and LNA (low noise amplifier) specially adapted with BIAS-T for HackRF One, AirSpy, SDRPlay and RTL-SDR V3 usb stick. It highly increases the reception performance (+ 11dB to + 23dB) and
This RF adapter allows is equipped with an SMA Male connector on both sides.It allows to connect for example 2 cables or connectors in SMA female.
This RF adapter allows is equipped with an SMA Female connector on both sides.It allows to connect for example 2 cables or connectors in SMA Male.
This LNA and SAW filter from Nooelec is specially designed to operate on 1.5Ghz Outernet frequency band and for Inmarsat radio applications, covering from 1.50GHz to 1.58GHz. It significantly
This band-cut filter is design by RTL-SDR.com, it blocks and reject broadcast FM band between 88 to 108 MHz with over 50dB of attenuation. Insertion loss is less than 0.5 dB between 0-1 GHz, and less
This BT4G-based BIAS-TEE is used to power a LNA or a 10Ghz PLL LNB to receive the QO-100 / Es'Hail2 satellite.The BT4G covers the frequency bands from 30 MHz to 4 GHz. The +/- supply leads are
This wide-band LNA preamp improves reception performance from 50 Mhz to 4 Ghz, it is based on SPF5189Z, with a noise factor of less than 1 dB.This LNA is designed to be powered by BIAS-T with a power
This bandpass filter for the 2.4 Ghz (13cm) allows to reject the local oscillator and harmonics frequencies of the Up-Converter for QO-100 to get a clean signal on the satellite, with a max. input
This filter for the 868 Mhz bandpass improves selectivity and suppresses spurious signals outside the 868Mhz band.Utilization type unlicensed ISM bande 868 Mhz: Sigfox, LoRa, LoRaWAN.Supplied with: 1
This milled aluminum milled box is specially designed for the RF protection of PCBs from F1OPA Design: LNA VHF-UHF, Bias-T, 2.4Ghz amplifier, SAW 868Mhz filters, ADS-B, QO-100 2.4Ghz and HF LNA.Case
PowerBlast 30 2.4 Ghz 30W amplifier, LDMOS semiconductor, compatible for amateur radio activities on the QO-100 satellite.Operates with a 32V power supply and an input power of 400 mW (26 dBm) for a
Be the first to ask a question about this product!
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal