Our store uses its own and third-party cookies to improve our services, secure transactions and enable tracking. To give your consent to its use, press the Accept button or choose Cookies.
Please note that refusing the Paypal cookie will prevent this payment method from being displayed and working in our store.
Viewed products
This balun is the perfect accessory to connect...
Online only
This balun is the perfect accessory to connect a long wire antenna, for example with the converter HF SDR Ham it Up to listen shortwave and HF bands from 0.5 to 30Mhz, but this balun can work up to 90MHz.
It has a high quality SMA female for connecting a coaxial cable, with protection against electrostatic discharge.
Balun One Nine Nooelec includes an Antenna Guard varistor on input to protect your SDR equipment from spurious ESD. The ESD protection is excellent, it passes an 8kV contact discharge test with a response time of only 300ps.
Very small, the balun 1:9 measures 39.2mm x 13mm (with connectors), light, with low insertion loss of -1.3dB (typical) and a maximum input power of + 28dBm.
Comes with: 1 official 1: 9 balun Nooelec.
Nooelec's Ham It Up v1.3 is an up-converter HF, equipped with the 125Mhz filter soldered on the PCB and allows to listen to all MF / HF bands from 0.5 to 50 Mhz, in all modes of modulation, from a
54,17 €tax excl.
SMA Male UHF Female (SO-239) Adapter.
4,17 €tax excl.
SMA Male to UHF Male Adapter. RG 316 coaxial cable 50 ohms, about 15cm long.
6,25 €tax excl.
Pigtail RF adapter SMA Male to SMA Male to connect for example a converter Ham it up to a HackRF One, or SDRPlay, and any device with a SMA female connector. Coaxial cable RG 316 50 ohms. Available in
4,17 €tax excl.
This Mini-Whip SDR active antenna allows reception of HF frequencies from 0 to 50 mhz with an SDR receiver.Compact in size, the mini-whip active antenna can be used independently with a 9-volt battery
20,75 €tax excl.
The LNA HF from F1OPA is a pre-amplifier and a low-pass filter (LNA), very powerful (+18dB to +20dB), with SMA Female connectors, for HF frequencies and short waves from 500 kHz to 30 MHz, with
28,75 €tax excl.
This RF adapter allows is equipped with an SMA Male connector on both sides.It allows to connect for example 2 cables or connectors in SMA female.
3,75 €tax excl.
Allows to control by USB the change of frequencies of an SDR software and to get a classic operation of a VFO on a radio hardware SDR!Fully configurable with the supplied software, Shuttle Xpress is
Cable SMA Male to SMA Male with 50-ohm coaxial cable low loss KSR195 for use from 0 to 6GHz.Length: 0,5m (50cm), 1, 3 or 5 metersConnector 1: SMA MaleConnector 2: SMA Male
7,42 €tax excl.
This band-cut filter is design by RTL-SDR.com, it blocks and reject broadcast FM band between 88 to 108 MHz with over 50dB of attenuation. Insertion loss is less than 0.5 dB between 0-1 GHz, and less
20,42 €tax excl.
Diamond BU50/A balun 1:1, genuine, operates from 1.7 to 40Mhz and allows to receive and transmit on HF bands.Technical data sheet of the HF BU50A balun:● Operating frequency from 1.7 to 40MHz●
30,69 €tax excl.
Genuine Diamond BU55 balun 1:1, operates from 3 to 75Mhz, allows to receive and transmit on HF bands + 6 meters (50Mhz).Technical data sheet of the HF BU55 balun:● Operating frequency from 3 to 75MHz●
23,25 €tax excl.
The new version Nooelec Balun 1:9 v2 allows to add a wired or dipole antenna type to listen HF bands from 0 to 30Mhz from the Ham It Up converter, an SDRPlay receiver or equivalent covering the HF
20,24 €tax excl.
Nooelec VHF-UHF antenna pack for SDR reception on VHF and UHF bands, supplied with a magnetic base, 2m RG58 coaxial cable with male SMA connector and 3 antenna strands to screw on the base:1
14,08 €tax excl.
The M0CVO high power 1:1 Balun operates from 1.8 to 30MHz. It can handle up to 400W CW or 450W PEP in SSB. It is used to match a balanced antenna, such as a dipole, to an unbalanced feed such as
38,25 €tax excl.
The M0CVO high power 4:1 Balun operates from 1.8 to 54MHz. It supports up to 400W CW or 500W PEP in SSB. It is used to convert the 200Ω impedance seen at the feed point of a bent or off-centre fed
38,25 €tax excl.
The M0CVO 9:1 UNUN Balun operates from 1.8 to 54MHz and supports up to 400W CW or 500W PEP in SSB. It provides a power point for a long-wire radiating element and converts the 450Ω (+/-) impedance to
38,25 €tax excl.
Balun 4:1 QRO for very high power M0CVO Antennas for Windom antennas, dipoles, fed loops or folded off centre. RF power of 1kW, for intermittent amateur use and not for continuous AM broadcast use.
57,50 €tax excl.
The 1:1 M0CVO very high power RF balun of 1kW (CW) and 1.2kW (PEP)*. It is used to adapt a balanced antenna, such as a dipole, to an unbalanced feed such as a coaxial cable. It also reduces the amount
57,50 €tax excl.
Click here to leave a review
Be the first to ask a question about this product!
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal