BladeRF 2.0 micro xA4/xA9 has a receive / transmit frequency in SDR from 47 MHz to 6 GHz, with a sampling frequency of 56 MHz (61.44 MHz maximum) and a 2×2 MIMO broadcast.
Works with the libbladeRF library, the bladeRF 2.0 mini is compatible with GNURadio, GQRX, SDR-Radio, SDR#, gr-phosphor, SoapySDR, etc. under Windows, Linux and macOS.
The xA4 features a 49KLE Intel Cyclone V FPGA including 38KLE freely programmable. The xA9 includes the larger FPGA at this time with 301KLE, including the programmable 294KLE.
PLL card allows the micro bladeRF 2.0 to drive VCTCXO MEMS on a 10 MHz reference signal.
Supplied with: bladeRF 2.0 mini xA4 or xA9 to choose below, (Intel 49KLE FPGA Cyclone V) or xA9 (301KLE), USB 3.0 SS cable, 2 SMA cables.
The HackRF One is a SDR receiver-transmitter covering from 1MHz to 6GHz in all available modes, analog and digital.Tip: For use in the lab, or with strong signals nearby, the sensitivity of the device
SMA Male to N Female Adapter. Coaxial cable RG 316 50 ohms. Available in 15cm, 50cm or 1 meter length (to choose from below).
Pigtail RF adapter SMA Male to SMA Male to connect for example a converter Ham it up to a HackRF One, or SDRPlay, and any device with a SMA female connector. Coaxial cable RG 316 50 ohms. Available in
Cable SMA Male to SMA Male with 50-ohm coaxial cable low loss KSR195 for use from 0 to 6GHz.Length: 0,5m (50cm), 1, 3 or 5 metersConnector 1: SMA MaleConnector 2: SMA Male
SDR Transceiver wide-band from 70 MHz to 6 GHz without gap and with 56 MHz of instantaneous bandwidth on the screen. The Ettus USRP B200 MINI operates in full duplex mode and is powered by USB 3.0
This directional Log Periodic antenna is designed in PCB and operates from 850MHz to 6,5GHz with 5-6 dBi gain. Works with Ettus USRP B200mini and all equipment operating in this frequency range. The
The bladeRF x40 from Nuand is a SDR transceiver full-duplex from 300 MHz to 3.8 GHz, all analog and digital modes, with appropriate software. 2 connectors antenna SMA female, Altera Cyclone IV FPGA.
SDR Transceiver B210 wide-band from 70 MHz to 6 GHz without gap and with 56 MHz of instantaneous bandwidth on the screen, MIMO (2 Tx & 2 Rx). The Ettus USRP B210 operates in full duplex mode,
This connector is a male SMA terminator endowed with a dummy load 50 Ohms for a maximum power of 1 watt on frequencies from 0 to 6Ghz. Connectors end 1: SMA maleConnectors end 2: Dummy load 1W max
Official case for the Nuand bladeRF 2.0 micro, version xA4 and xA9. A set of screws is included for assembly. The case is made of polycarbonate material high density, transparent and very
MoRFeus is a broadband frequency generator and upconverter & downconverter from 30 MHz to 6 GHz. With LCD screen and front adjustment knob. MoRFeus is specifically designed to operate in 85 MHz to
SDR Transceiver from 70 MHz to 6 GHz with 56 MHz of instantaneous bandwidth. The Ettus USRP B205MINI operates in full duplex mode 1x1 and is powered by USB 3.0 port. Size: 50 x 84 mmComes with:
This adapter is a SMA attenuator available in version -3, -6, -10, -15, -20 or -30dB for frequencies from 0 to 6 Ghz.Connector end 1: SMA maleConnectique end 2: SMA femaleImpedance: 50 OhmsPower
The BT-100 is a TX power amplifier, powered by Bias-T, to connect to the SMA TX socket of the bladeRF 2.0 micro xA4 and xA9.MMIC: PHA-1H +TX frequency: 50 MHz to 6 GHzConsumption: 200mWBlue LED power
The BT-200 is a RX LNA, powered by Bias-T, to connect to the SMA RX socket of the bladeRF 2.0 micro xA4 and xA9.MMIC: TSS-53LNB+TX frequency: 500 MHz to 5 GHzConsumption: 300mWGreen LED power
The XTRX PRO is the first embedded SDR in Mini PCI format and with RX and TX in Full-Duplex (2x2 MIMO) for frequencies from 30Mhz to 3.8Ghz, stabilized with integrated GPSDO, sampling rate up to 120
Be the first to ask a question about this product!
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal