The LoStik dongle is LoRa, LoRaWAN and The Things Network (TTN) compatible, easy to use directly from a PC or Raspberry PI.
It enables IoT (Internet of Things) integrators, 868Mhz wireless network testers, and radio enthusiasts to connect more quickly to a LoRa network, diagnose network problems, and build 868Mhz connected devices.
Delivered with: 1 Lostik dongle, 1 plastic case.
- Connectivity: USB 2.0
- Works with any PC, Raspberry Pi or BeagleBone
- Simple ASCII interface
- LoRa or LoRaWAN mode support
- Compatible with The Things Network (TTN)
- Based on the Microchip R2483 chipset
- 2 programmable LEDs
- Developed in open source (Github)
- Power consumption: 140 mA TX, 20 mA at rest (with power LED)
- Sensitivity of the receiver: -146 dBm
- TX power: adjustable up to +18,5dBm (70mW max.)
- Dimensions: 80 mm x 25 mm x 12 mm (without antenna)
Be the first to ask a question about this product!
PCB antenna Yagi 3 elements for 868MHz with a gain of 8dBi, for long-range use on the ISM 868Mhz frequency band and LPWAN / LoRaWan networks (Sigfox, LoRa), RFID UHF and Zigbee. The antenna is
This filter for the 868 Mhz bandpass improves selectivity and suppresses spurious signals outside the 868Mhz band.Utilization type unlicensed ISM bande 868 Mhz: Sigfox, LoRa, LoRaWAN.Supplied with: 1
868 Mhz antenna with 2dbi gain, SMA male right angle connector for hardware device on 868Mhz ISM band and LoRa / LoRaWan application.Frequencies: 868 Mhz +/- 3MhzConnector: SMA male - right angleGain:
Antenna stubby for ISM LoRa 868 Mhz band, 4cm long with 2dbi gain, SMA male connector.Frequencies RX and TX: 868 MhzConnector: SMA maleGain: 2dBiSWR: ≤1.5Polarization Type: VerticalMaximum power:
This LoRaWAN network node is an IoT development board for LoRa 433Mhz or 868Mhz (depending on the model) with WIFI 802.11 b/g/n/e/i, Bluetooth/BLE and 2.4cm OLED display.Compatible with the Arduino
This single-channel LoRa gateway for Raspberry Pi is an inexpensive device to start experimenting with a 868 Mhz LoRa network. It allows to receive LoRa packets on a specific channel and to share them
This EBYTE E32 module is a 100mW long range transceiver with UART interface, available in 433Mhz or 868Mhz version and based on SEMTECH chip SX1276 (868Mhz) and SX1278 (433Mhz) for LoRa network and
This LoRa tracker is an IoT development board for LoRa 433 Mhz or 868 Mhz frequencies (depending on the model), with WIFI 802.11 b / g / n connection, Bluetooth / BLE, 2.4cm OLED display (soldering),
The IoT LoRa Raspberry Pi HAT allows to create an economical LoRa gateway compatible with The Things Network (TTN) on the ISM Europe 868Mhz band.This HAT for Raspberry Pi allows you to configure your
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal