The RigExpert AA-55 ZOOM Bluetooth is designed...
The RigExpert AA-55 ZOOM Bluetooth is designed to measure SWR (Standing Wave Ratio), return loss, cable loss, and other parameters of cable and antenna systems in the range from 60 kHz to 55 MHz .
A built-in ZOOM function makes graphical measurements particularly effective.
The following tasks are easily accomplished using this analyzer:
Quick check of an antenna, tune an antenna to resonance, comparison of the characteristics of an antenna before and after a particular event (rain, hurricane, etc.), realization of coaxial stubs or measurement of their parameters, cable test and fault location, measurement of cable loss and characteristic impedance, and measurement of capacitance or inductance of reactive loads.
Delivered with: 1 Rig Expert AA-55 ZOOM Bluetooth, 1 soft case, 1 USB cable, 1 user manual, 1 set of alkaline batteries.
Frequency range: 0.06 to 55 MHz
Frequency input: 1 kHz resolution
Measurement for 25, 50, 75, 100, 150, 200, 300, 450 and 600 - Ohm systems
SWR measurement range: 1 to 100 in digital mode, 1 to 10 in graphics mode
SWR display: digital or analog indicator
R and X range: 0 ... 10000, -10000 ... 10000 in digital mode,
0 ... 1000, -1000 ... 1000 in graphics mode.
- TOS at one or more frequencies
- SWR, return loss, R, X, Z, L, C and phase angle at a single frequency.
- TOS graph, 100 points
- R, X diagram, 100 points
- Smith diagram, 100 points
- Return loss table, 100 points
- Cable tools (loss and characteristic impedance)
Optional calibration at open short load.
- 10 locations to save measurement results
- Connector type: UHF Female (SO-239)
- Output signal shape: square, 0.06 to 55 MHz
- Output power: +13 dBm (at a load of 50 Ohms)
- 2 alkaline batteries of 1.5 V, type AA or 2 Ni-MH batteries of 1.2 V, type AA *.
- Max. 4 hours of continuous measurement, max. 2 days in standby mode when fully charged batteries are used.
- When the analyzer is connected to a PC or to a DC adapter with USB socket, it is powered by these sources.
- 320 × 240 color TFT screen
- 6 × 3 keys on the waterproof keyboard
- Multilingual menus and help screens
- USB connection to a personal computer
Bluetooth specification v.2.0, Class B. Compatible with Android OS ver. 4.0 and above.
Dimensions: 103 mm x 207 mm x 37 mm
Operating temperature: 0 to 40 ° C
Weight: 310 g without batteries
2 years warranty
The RigExpert AA-55 ZOOM Bluetooth is made in Ukraine.
* Batteries are not supplied with the analyzer.
The structure diagram of the Rig Expert AA55 ZOOM Bluetooth solution:
Diagram of the resistive bridge and its connection to the mixer:
The switch which is controlled by the central unit feeds the signal from the certain side of the bridge to the mixer chip. When the load is fully active and its resistance is 50 Ω, the bridge is balanced and the switch emits the same signal in both positions. This eliminates the need to calibrate the analyzer, and also gives very good accuracy around SWR = 1.
Frequency range 1-3000 MHz, 2 ports VNA with S11 and S21, RF Generator with output power of -6dBm @ 500 MHz, Low power consumption, 370mA @ 5 V, SMA connectors, boot loader for future firmware
465,83 €tax excl.
The mini-VNA Pro² BT is a portable VNA antenna and network analyzer that covers from 0.1 to 230Mhz, it has a 1000mAh internal Li-ion battery and a new Bluetooth interface to let use the mini-VNA Pro
387,50 €tax excl.
This calibration kit can be used with any SMA connector device, such as the MiniVNA Tiny and PRO2 or NanoVNA and any VNA.The SMA calibration kit consists of a dummy load of 50 ohms, an open circuit
26,58 €tax excl.
The NanoVNA-F Deepelec version is the enhanced version of the open-source Antenna and Vector Network (VNA) analyzer that covers the HF, VHF and UHF bands from 50 KHz to 1500 MHz with metal case and
99,17 €tax excl.
This RF NanoVNA demo kit consists of a PCB which allows you to test or demonstrate the 18 RF functions or components listed below.This RF test card is recommended for demo and use with VNA antenna
32,42 €tax excl.
This NanoVNA RF demo kit is composed of a PCB to assemble, to perform tests or demonstration of RF integrated circuit (DIP) and SMT (SMT) components.Adapted to work with vector network analyzer
4,13 €tax excl.
The RigExpert AA-650 (former AA-600) is a powerful antenna analyzer designed to test, verify, tune or repair antennas and antenna feed lines operating from 0.1 to 650 Mhz and with bluetooth. The
715,83 €tax excl.
The RigExpert Stick-230 antenna analyzer is designed to measure SWR (standing wave ratio), return loss, and other parameters of cable and antenna systems in the 100 kHz range at 230 MHz . It has an
304,17 €tax excl.
The RigExpert AA-35 ZOOM is a portable, self-calibrating analyzer designed to measure SWR (standing wave ratio), return loss, cable loss, from 60 kHz to 35 MHz , with a capacity zoom. Frequency range:
282,50 €tax excl.
The RigExpert Stick Pro is a vector analyzer (VNA) of antennas and cables. The analyzer allows you to measure various parameters of antennas, cables, lines, filters and many more in the frequency
The RigExpert AA-230 ZOOM antenna analyzer with Bluetooth 4.0, allows measurement of SWR, return loss, cable loss, in the frequency range 100 kHz to 230 MHz . The integrated ZOOM function makes
371,29 €tax excl.469,00 € -5%
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal