The new version Nooelec Balun 1:9 v2 allows to add a wired or dipole antenna type to listen HF bands from 0 to 30Mhz from the Ham It Up converter, an SDRPlay receiver or equivalent covering the HF bands.
The difference with version V1, is that it allows to go down in frequency, as well as to have 3 different types of connectors included for the antenna or the long wire.
The Nooelec Balun 1:9 V2 includes an AntennaGuard varistor to protect the SDR receiver from spurious electrostatic discharges and connector to receiver is in SMA female.
With a size of 38mm x 25mm, this balun is a little larger than the V1 and also offers better HF performance in low HAM band with very low insertion loss and maximum input power of + 24dBm.
Delivered with: 1 Nooelec official 1: 9 V1 balun, original warranty.
Nooelec's Ham It Up v1.3 is an up-converter HF, equipped with the 125Mhz filter soldered on the PCB and allows to listen to all MF / HF bands from 0.5 to 50 Mhz, in all modes of modulation, from a
SMA Male UHF Female (SO-239) Adapter.
SMA Male to UHF Male Adapter. RG 316 coaxial cable 50 ohms, about 15cm long.
Pigtail RF adapter SMA Male to SMA Male to connect for example a converter Ham it up to a HackRF One, or SDRPlay, and any device with a SMA female connector. Coaxial cable RG 316 50 ohms. Available in
This Mini-Whip SDR active antenna allows reception of HF frequencies from 0 to 50 mhz with an SDR receiver.Compact in size, the mini-whip active antenna can be used independently with a 9-volt battery
The LNA HF from F1OPA is a pre-amplifier and a low-pass filter (LNA), very powerful (+18dB to +20dB), with SMA Female connectors, for HF frequencies and short waves from 500 kHz to 30 MHz, with
This RF adapter allows is equipped with an SMA Male connector on both sides.It allows to connect for example 2 cables or connectors in SMA female.
Allows to control by USB the change of frequencies of an SDR software and to get a classic operation of a VFO on a radio hardware SDR!Fully configurable with the supplied software, Shuttle Xpress is
This balun is the perfect accessory to connect a long wire antenna, for example with the converter HF SDR Ham it Up to listen shortwave and HF bands from 0.5 to 30Mhz, but this balun can work up to
Cable SMA Male to SMA Male with 50-ohm coaxial cable low loss KSR195 for use from 0 to 6GHz.Length: 0,5m (50cm), 1, 3 or 5 metersConnector 1: SMA MaleConnector 2: SMA Male
This band-cut filter is design by RTL-SDR.com, it blocks and reject broadcast FM band between 88 to 108 MHz with over 50dB of attenuation. Insertion loss is less than 0.5 dB between 0-1 GHz, and less
Diamond BU50/A balun 1:1, genuine, operates from 1.7 to 40Mhz and allows to receive and transmit on HF bands.Technical data sheet of the HF BU50A balun:● Operating frequency from 1.7 to 40MHz●
This high-pass notch filter is designed by RTL-SDR.com and rejects the AM broadcast from 500 kHz to 1.7 MHz, with attenuation of more than 50dB. In fact, because of the attenuation, the filter is
Genuine Diamond BU55 balun 1:1, operates from 3 to 75Mhz, allows to receive and transmit on HF bands + 6 meters (50Mhz).Technical data sheet of the HF BU55 balun:● Operating frequency from 3 to 75MHz●
Laminated HamRadio Guide booklet, 2021 edition, 50 pages in A4 format (219 x 297 mm), in english bound by metal rings, for use at the station or on a laptop, in SOTA or IOTA. This booklet can be used
Be the first to ask a question about this product!
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal