New version of the SDRPlay wideband receiver, the RSP1A now covers all frequencies from 1 kHz to 2 GHz without hole, all modes, with up to 10 MHz bandwidth on the screen and 14-bit sampling.
In addition, the new SDRPlay RSP1A features 11 band filters that switch automatically according to the frequency used, an adjustable gain LNA preamp, a 0.5 PPM TCXO and a 4.7V BIAS-T power supply.
The RSP1A works with SDR software on Windows, Mac and Linux such as: SDRUno (official software recommended), SDR Console, HDSDR and CubicSDR.
All you need to run the SDRPlay is a computer or a Raspberry, a USB cable and an antenna to have a receiver-scanner broadband, powerful, all modes.
Supplied with: SDRPlay RSP1A assembled in plastic case (without power cable).
See below the recommendations for use, installation and support request SDRplay.
Receive 1kHz to 2GHz
Up to 10 Mhz bandwidth on the screen
Adjustable LNA gain
AM / FM / DAB bandstop filters
RF shielding in the plastic housing
Antenna connector: SMA female
Open API allows developers to create new applications around the receiver.
Compatible with SDR software on Windows, Mac, Linux: SDRUno (recommended), HDSDR, SDR Console, CubicSDR (Mac / Linux)
Consumption: 120-175mA (without BIAS-T enabled)
Equipped with 11 band filters:
2 - 12MHz
12 - 30 Mhz
30 - 60MHz
60 - 120MHz
120 - 250MHz
250 - 300MHz
300 - 380Mhz
380 - 420Mhz
420 - 1000MHz
3 notch filters
FM: 85 - 100Mhz (> 50dB)
MW: 600 - 1550Mhz (> 30dB)
DAB: 165 - 230 Mhz (> 30dB)
2 years warranty
You will find an online tutorial for quick installation of the RSP1-A: http://www.sdrplay.com/start-here/
To download the latest SDRPlay drivers and software for Windows, Mac, Linux and Android: http://www.sdrplay.com/downloads/
Compatibility with Android smartphone or tablet: To date only the first generation RSP1 version is compatible with an Android smartphone or tablet and the SDRTouch software, with the installation of the android driver SDRPlay for SDR Touch. The Android version 7.0 is not yet supported by this driver that works for Android versions 3.1 to 6. The new version RSP1A and the RSP2 and RSP2PRO are not compatible with Android and SDRTouch currently.
1 - Do not connect the RSP1A directly to the same antenna as your transmitter, or to an antenna in the near field of a transmitting antenna as this may cause irreversible damage.
2 - The RSP1A is sensitive to electrostatic discharge which can damage the receiver if not protected or used correctly. It is recommended to disconnect the antenna in case of severe weather and to ensure an earthing of the antenna. Before reconnecting the coaxial cable after a thunderstorm, it is imperative the unloader (braid and core) to the ground.
In these 2 cases of loss of reception and RF damage, the warranty will not apply and the equipment neither repaired, exchanged or refunded. The signs of RF damage are characterized by signs of hot on or around components near the signal input, a burning smell is also an indication of RF damage.
For any support request, SDRPlay offers an online platform to get in touch directly with the technical support team for our customers : Request for official support SDRPlay.
SDRuno v1.4 for Windows, check last update at www.sdrplay.com/windl2.php
SDRuno Software User Guide by Paul NN4F and Mike KD2KOG v1.4
Manual SDRuno 1.4 in French (translation by Claude de F0ELA).
Plugin for SDRuno software and support for USB Shuttle Xpress and PRO V2
SMA Male UHF Female (SO-239) Adapter.
SMA Male to UHF Female Adapter. RG 316 coaxial cable 50 ohms, about 15cm long.
Pigtail RF adapter SMA Male to SMA Male to connect for example a converter Ham it up to a HackRF One, or SDRPlay, and any device with a SMA female connector. Coaxial cable RG 316 50 ohms. Available in
This Mini-Whip SDR active antenna allows reception of HF frequencies from 0 to 50 mhz with an SDR receiver.Compact in size, the mini-whip active antenna can be used independently with a 9-volt battery
This RF adapter allows is equipped with an SMA Male connector on both sides.It allows to connect for example 2 cables or connectors in SMA female.
Allows to control by USB the change of frequencies of an SDR software and to get a classic operation of a VFO on a radio hardware SDR!Fully configurable with the supplied software, Shuttle Xpress is
This balun is the perfect accessory to connect a long wire antenna, for example with the converter HF SDR Ham it Up to listen shortwave and HF bands from 0.5 to 30Mhz, but this balun can work up to
Cable SMA Male to SMA Male with 50-ohm coaxial cable low loss KSR195 for use from 0 to 6GHz.Length: 0,5m (50cm), 1, 3 or 5 metersConnector 1: SMA MaleConnector 2: SMA Male
The new SDRPlay RSPduo is a 14-bit SDR dual receiver that covers from 1kHz to 2GHz (without hole), with dual-tuner (simultaneous reception on 2 different antennas). The SDRDuo is equipped with a
VHF-UHF telescopic dipole antenna pack for SDR reception and with a flexible tripod and suction pad. This antenna set includes 1 dipole antenna support with 60cm of cable and with male SMA connector,
The Shuttle PRO V2 Contour Design allows to control the frequency of a SDR software and to retrieve the classic operation of a VFO on SDR radio equipment!The Shuttle PRO V2 includes 15 programmable
Hi-Quality USB 2.0 Vention print cable Male A - Male B, high-speed and ferrite cable for protection against interference and interference.This cable is used to power a printer or scanner, as well as
The new version Nooelec Balun 1:9 v2 allows to add a wired or dipole antenna type to listen HF bands from 0 to 30Mhz from the Ham It Up converter, an SDRPlay receiver or equivalent covering the HF
The new SDRPlay RSPdx receiver is the replacement of the RSP2PRO, it covers from 1kHz to 2GHz (without hole) with 10MHz of the spectrum on the screen, 14-bit sampling, with TCXO 0.5PPM, notch filter
MLA-30 Plus magnetic loop active antenna for receiving HF bands from 500 kHz to 30 MHz.The MLA-30+ antenna can be used with the RTL-SDR V3 stick in direct conversion mode, with the Ham it up
Active Whip mini-antenna for receiving HF frequencies from 10khz to 30 mhz with an SDR receiver or a short and HF receiver. Antenna connector: SMA female.This active antenna need to be powered with
The Passion Radio SDR Deluxe Plus V4 pack provides reception coverage between 0.5 to 1766 MHz from a computer running Windows, Mac or Linux.This V4 version of the pack includes:- 1 RTL-SDR.com V3
Be the first to ask a question about this product!
Stock and shipped from France
14 days to return, 2 warranty
Response within 24h to 72h
SSL, VISA, Mastercard, Paypal